DeWalt DCH966 Traducido De Las Instrucciones Originales página 36

EnGLIsH
1. Attach the left side handle
screw 6 located inside the end of the handle. Fully tighten
with 5mm hex wrench
2. Attach the right side handle
screw 4 located inside the end of the handle. Fully tighten
with 5 mm hex wrench
nOTE: Side handles
3
proper orientation with the key on the end of the grip
facing down.
nOTE: Store the 5mm hex wrench
wrench retainer 17 .
Inserting and Removing 28mm Hex
Accessories (Fig. G)
This machine uses chisels with a 28mm hex shank. We
recommend to use professional accessories only.

WARNING: Since accessories other than those offered
by D WALT have not been tested with this product,
e
the use of such accessories may entail hazardous
situations. To reduce the risk of injury, use only accessories
recommended by D
e
Clean the chisel shank.

WARNING: Do not apply lubricant to the machine.
To fit a chisel with notch in the shank,
proceed as follows (Fig. G)
1. Pull the tool retainer 25
unlock position.
2. Hold the chisel in front of the tool holder with the notch
facing downwards.
3. Insert the chisel shank 27
tool holder 14 .
4. Rotate the tool retainer
lock position to lock the accessory in position.
5. Pull on the chisel to check if it is properly locked. The
hammering function requires the chisel to be able to move
axially several inches when locked in the tool holder.
6. To remove a chisel pull the tool retainer
180° to the unlock position and pull the chisel out of the
tool holder.

WARNING: Always wear gloves when you change
accessories. The exposed metal parts on the tool and
accessory may become extremely hot during operation.
34
5 with hex head
16 (supplied).
3 with hex head
16 (supplied).
and 5 must be installed in the
in the hex
16
WALT.
and rotate it 180° to the
into the 28mm hex
25 180° so it slides back into the
25 and rotate it
Service Indicator LED (Fig. A, H)
Your breaker has yellow service indicator LED
when service is required. Refer to the table for more information
on LED functionality.
LED Function
Yellow
(permanently on)
Yellow
(flashing)
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
26
start-up can cause injury.

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: Be aware of the location of pipework
and wiring.

WARNING: Apply a pressure of approximately 22-44 lbs.
(10-20 kg) to the tool. Applying excessive force does not
speed up chiseling and can decrease tool performance and
may shorten tool life.
Proper Hand Position (Fig. J)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
IMPORTanT: The tool must be held with two hands at all times
when in use.
Horizontal Applications (Fig. J)
Proper hand position requires one hand on the bail/loop style
auxiliary handle 8
Vertical Applications (Fig. J)
Proper hand position requires both hands on the left handle
and right handle 3
13
Description
service required
The yellow service indicator
LED 13 lights up to indicate
the tool needs servicing within
the next 10 hours of use (new
lubrication and hammer
mechanism sealing).
service exceeded
With the service indicator lit,
after a further 10 hours of use
the service indicator flashes to
indicate the tool has exceeded
the required service interval.
with the other hand on the top handle
.
, to indicate
1 .
5