Publicidad
Idiomas disponibles
Idiomas disponibles
E ViCE A
ADJ
STMENTS
TO REPLACE BELTS (See Fig. 24)
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended thatthe belt(s) be replaced
by a Sears Parts & Repair Center.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
The V-belts on your snow thrower are ofspecial construction
and should be replaced by original equipment manufac-
turer (OEM) belts available from your nearest Sears Parts
& Repair Center. Using other than OEM belts can cause
_ersonal injury or damage to the snow thrower.
&
WARNING: Belt replacement
requires
separation of the snow thrower. While
separating the auger housing from the
frame
assembly,
it is important that
an assistant
stand in the operating
position
and hold the snow thrower
handles.
Serious
personal
injury and/
or damage to the unit could occur if the
snowthrower
should fall during the belt
changing
process.
FRAME
ASSEMBLY
AUGER
HOUSING
HANDLES
1.
REMOVE GASOLINE
FROM FUEL TANK - Drain
gasoline from fuel tank into a suitable container, out-
doors, away from fire or flame. Wipe up any spilled
gasoline.
2.
REMOVE DISCHARGE
CHUTE
- Loosen Iocknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
3.
REMOVE BELT COVER - See "TO REMOVE BELT
COVER" in this section of this manual.
4.
REMOVE ENGINE PULLEY- Remove bolt, Iockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
5.
SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts and lock washers holding
_
WARNING:
As
the
last
bolt
is
removed,
I
have your assistant
carefully
lower the
|
J
.
7.
REMOVE AUGER BELT from around pulley.
RELIEVE TENSION ON TRACTION
DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.
HINT: Insert a 3/8" drive ratchet (in the "ON" position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
8.
With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
9.
Place auger belt around and inside the groove of auger
pulley only.
10. While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
become dislodged from the pulley (by catching the idler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 10. Belt
must be fully seated in pulley groove when bringing
the snow thrower together.
12. Install the two (2) hex bolts and lock washers and
tighten securely.
13. INSTALL ENGINE PULLEY- Place belt in pulley groove
and slide pulley on crankshaft. Install flat washer, lock-
washer and bolt and tighten securely (35-40 ft. Ibs. /
41-47 N-m torque). Make sure belt is inside belt keeper.
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE - See "INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD" in the
Assembly / Pre-Operation section of this manual.
HOLE
BELT
FRAME
AUGER
HOUSING
BO_
LOCK
WASHER
18
FiG.24
Publicidad
