Descargar Imprimir esta página

Craftsman 152.219070 Manual De Instrucciones página 6

Publicidad

Idiomas disponibles

Idiomas disponibles

SPECIFIC
SAFETY
iNSTRUCTiONS
ALWAYS WEAR EYE PROTECTmON, Any power tool
can throw debris into the eyes during operations, which
could cause severe and permanent eye damage.
Everyday eyeglasses are NOT safety glasses.
ALWAYS wear Safety Goggbs (that comply with ANSi
standard Z87.1) when operating power toob. Safety
Goggbs are availabb at Sears Retaib Stores.
Basic precautions should always be followed when
using any power tool. To reduce the risk of injury,
ebctrbal
shock or fire, comply with the safety rubs
listed below:
1.
READ and understand the instruction manual
before operating this power tool.
2,
DO NOT OPERATE THIS MACHINE until it is
assembled and installed according to the instruc-
tions,
3.
OBTAIN ADVICE FROM YOUR SUPERVISOR,
instructor, or another qualified person if you are not
familiar with the operations of this power tool.
4.
DO NOT leave any power tool plugged into the
electrical outlet. Unplug it from the outlet when not
in use and before servicing and cleaning.
5,
TO REDUCE THE RISK OF ELECTRICAL
SHOCK, do not use outdoors, Do not expose to
rain, Store indoors,
6,
FOLLOW all electrical and safety codes, including
the National Electric Code (NED) and the Occu-
pational Safety and Health Regulations (OSHA).
All electrical connections and wiring should be
made by qualified personnel only.
7.
DO NOT handle the plug or mortiser with wet
hands.
8.
CONNECT power tool to a properly grounded outlet
only. See grounding instructions.
9,
SECURE THE MACHINE TO A SUPPORTING
SURFACE,
Vibration can cause the machine to
slide, walk, or tip over,
10, NEVER START THE MACHINE with the drill bit or
cutting tool against the workpiece, Loss of control of
the workpiece can cause serious injury.
11. PROPERLY LOCK THE DRILL BIT OR CUTTING
TOOL IN THE UNIT before operating this machine.
12. ADJUST the depth stop to avoid drilling into the
table.
13. DO NOT attempt to mortise material that does not
have a fiat surface, unless a suitable support is
used.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
USE ONLY DRILL BITS, CUTTING TOOLS, OR
OTHER ACCESSORIES
with shank size recom-
mended in your instruction manual. The wrong size
accessory can cause damage to the machine
and/or serious injury.
USE ONLY DRILL BITS OR CUTTING TOOLS
that are not damaged. Damaged items can cause
malfunctions that lead to injuries.
ALWAYS position the hold-down directly over the
workpiece to prevent the workpiece from lifting
during operation. Loss of control of the workpiece
can cause serious injury.
TURN THE MACHINE "OFF" AND WAIT FOR
THE DRILL BIT, CUTTING TOOL, OR SANDING
DRUM TO STOP TURNING prior to cleaning the
work area, removing debris, removing or securing
work-piece, or changing the angle of the table, A
moving drill bit or cutting tool can cause serious
injury.
PROPERLY SUPPORT LONG OR WIDE work-
pieces, loss of control of the workpiece can cause
severe injury.
NEVER PERFORM LAYOUT, ASSEMBLY
OR
SET-UP WORK on the table/work area when the
machine is running, Serious injury can result,
TURN THE MACHINE "OFF", disconnect the
machine from the power source, and clean the
table/work area before leaving the machine.
REMOVE THE SWITCH KEY to prevent unauthor-
ized use. Someone else might accidentally start the
machine and cause serious injury to themselves.
REPLACE a damaged cord immediately. DO NOT
use a damaged cord or plug. if the power tool is not
operating properly, or has been damaged, left out-
doors or has been in contact with water, return it to
a Sears Service Center.
USE only as described in this manual. USE acces-
sories only recommended by Sears.
ADDITIONAL
INFORMATION
regarding the safe
and proper operation of this product is available
from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201 in the Accident
Prevention Manual for Industrial Operation and also
in the Safety Data Sheets provided by the NSC.
Please also refer to the American National
Standards institute ANSi 01.1 Safety Requirements
for Woodworking
Machinery and the U.S.
Department of Labor OSHA 1910.213 Regulations.
SAVE THESE INSTRUCTIONS.
Refer to them fie-
quently and use them to instruct other users.

Publicidad

loading