DeWalt D25966 Traducido De Las Instrucciones Originales página 23

Hex Wrench Storage (Fig. A, B)
When not in use the 5mm hex wrench
the hex wrench retainer
14
1. Pull the 5mm hex wrench
retainer 14 to remove it.
2. Push the 5mm hex wrench
retainer 14 to store it.
Bail/Loop Style Auxiliary Handle (Fig. C)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the bail/loop style auxiliary handle
properly installed when using the tool for horizontal
applications. Failure to do so may result in the bail/loop style
auxiliary handle slipping during tool operation and subsequent
loss of control. Hold tool with both hands to maximize control.
The bail/loop style auxiliary handle
housing and may be rotated 360˚ to permit right- or left-hand use.
Mounting the Bail/Loop Style Auxiliary
Handle (Fig. C)
1. Disassemble the bail/loop style auxiliary handle
the handle knob 9 by turning it counterclockwise until it
comes off the bail/loop style auxiliary handle
2. Pull the handle bolt 19
auxiliary handle .
8
3. Remove the bail/loop style auxiliary handle
handle assembly.
4. Slide the handle assembly onto the nose of the tool through
the handle ring opening
mounting location
18
5. Install the bail/loop style auxiliary handle
handle assembly.
nOTE: Ensure the teeth
handle 8 and the handle mount teeth
before proceeding.
6. Insert the handle bolt
the hexagon shaped opening
loop style auxiliary handle
nOTE: Do not insert the handle bolt
handle knob opening side
properly tighten.
7. Asemble the bail/loop style auxiliary handle
8. Rotate and pivot the bail/loop style auxiliary handle
the desired position.
9. Thread the handle knob
the handle knob opening side
auxiliary handle 8 .
10. Tighten the handle knob
bail/loop style auxiliary handle
13 should be stored in
.
13 from the hex wrench
13 into the hex wrench
8 clamps to the front of the
8
8 .
from the bail/loop style
from the
8
17 and onto the handle ring
located on the housing.
onto the
8
on the bail/loop style auxiliary
24
20 mesh together
19 into the handle assembly from
on the side of the bail/
21
8 .
19 from the
. The handle will not
22
8 .
9 onto the handle bolt
of the bail/loop style
22
9 by turning it clockwise until the
is secured in position.
8
Side Handles (Fig. A, D, E)

CAUTION: ALWAYS operate the tool with the side
handle properly assembled. Hold tool with both
hands to maximize control.
1. Attach the left side handle
screw 6
with 5mm hex wrench
2. Attach the right side handle
screw 4
with 5 mm hex wrench
nOTE: Side handles
proper orientation with the key on the end of the grip
facing down.
nOTE: Store the 5mm hex wrench
wrench retainer
Inserting and Removing 28mm Hex
Accessories (Fig. F)
This machine uses chisels with a 28mm hex shank. We
recommend to use professional accessories only.
. Loosen

WARNING: Since accessories other than those offered
by D
the use of such accessories may entail hazardous
situations. To reduce the risk of injury, use only accessories
recommended by D
Clean the chisel shank.

WARNING: Do not apply lubricant to the machine.
To fit a chisel with notch in the shank,
proceed as follows (Fig. F)
1. Pull the tool retainer
unlock position.
2. Hold the chisel in front of the tool holder with the notch
facing downwards.
3. Insert the chisel shank
tool holder
4. Rotate the tool retainer
lock position to lock the accessory in position.
5. Pull on the chisel to check if it is properly locked. The
hammering function requires the chisel to be able to move
axially several inches when locked in the tool holder.
8 to
6. To remove a chisel pull the tool retainer
180° to the unlock position and pull the chisel out of the
19 from
tool holder.

WARNING: Always wear gloves when you change
accessories. The exposed metal parts on the tool and
accessory may become extremely hot during operation.
5 with hex head
located inside the end of the handle. Fully tighten
(supplied).
13
with hex head
3
located inside the end of the handle. Fully tighten
13 (supplied).
and must be installed in the
3 5
14 .
WALT have not been tested with this product,
e
WALT.
e
and rotate it 180° to the
23
27 into the 28mm hex
.
12
180° so it slides back into the
23
EnGLIsh
13 in the hex
26
23 and rotate it
21