Descargar Imprimir esta página

Amica JSM 4011 Manual De Instrucciones página 15

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
appliance.
Electrical requirements
Make sure that the voltage in-
dicated on the nameplate cor-
responds to that of your home
electrical mains. Alternating
current must be used, typically
marked ~.
In accordance with European Directive 2012/19/
EU and Polish legislation regarding used electrical
and electronic goods, this appliance is marked with
the symbol of the crossed-out waste container. This
marking indicates that the appliance must not be
disposed of together with other household waste
after it has been used.
The user is obliged to hand it over to waste collection
centre collecting used electrical and electronic goods. The
collectors, including local collection points, shops and local
authority departments provide recycling schemes.
Proper handling of used electrical and electronic goods helps
avoid environmental and health hazards resulting from the
presence of dangerous components and the inappropriate
storage and processing of such goods.
SPECIFICATION:
Model - JSM 4011
Rated voltage - 220-240V~, 50/60Hz
Rated power - 200 W
Power cord - 1 m
Net weight - 4.7kg
FEATURES AND COMPONENTS (FIGURE 1)
1. Pusher
2. Hopper
3. Auger
4. Strainer (coarse)
5. Strainer (fine)
6. Juice collector
7. Cleaning brush
8. Separator container
9. Pulp outlet
10. Juice outlet
11. Juice outlet plug
12. Motor unit
13. Control Panel
14. Drive shaft
15. Pulp container
16. Juice container (1000 ml)
17. Silicone squeegee
BEFORE FIRST USE:
• After unpacking the appliance, make sure that all the
attachments are included and there are no visible signs
of damage.
• Before first use, wash in hot water all the attachments
which come into contact with food. In addition, thoroughly
dry all parts before use.
• Never immerse the body of the appliance in water or other
liquids. This can cause damage to the motor and pose a
risk of electric shock.
• Wash all food products before juicing. Cut large fruits,
such as apples, into smaller pieces to fit into the inlet.
• Do not use frozen products.
• Remove hard seeds and pits before juice extraction.
• Before assembling the appliance, make sure that the
power cord is disconnected from the wall outlet.
HOW TO USE YOUR APPLIANCE
1. Expand the power cord, place the body of the appliance
on a stable, dry and flat surface.
2. The order of assembly of individual components is shown
on Fig. 2a.
3. Make sure that the rubber protective buffer is fixed on the
pulp outlet hole at the bottom of the separator container
(Fig. 2b).
4. Make sure that the separator container gasket (Fig.
2i) and the juice outlet plug gasket (Fig. 2j) have been
installed correctly.
5. Place the separator container on the motor unit (Fig. 2a,
item 1) so that the two ridges in the motor unit fit into the
grooves in the bottom of the separator container (Fig. 2c).
Make sure that the components are properly connected.
6. Assemble the strainer and juice collector (Fig. 2d).
7. Place the combined elements (strainer and juice collector)
inside the separator container (Fig. 2f). Note that there
is a socket inside the container (partially covered by the
safety buffer) (Fig. 2e, item 2), and you need to fit the tab
located in the strainer (Fig. 2e, item 1) into the socket.
Make sure that the components are properly connected
(Fig. 2f).
8. Insert the worm shaft in the separator container unit along
with other fitted components (Fig. 2f). Make sure that the
worm shaft is properly mounted on the drive shaft and
the elements are properly connected. Otherwise, the
container will not close.
9. Close the separator container by putting the hopper on
(Fig. 2g). Put the hopper on the vessel in such a manner
that the triangle symbol on the separator container and
an open padlock symbol on the hopper were in a straight
line (Fig. 2f). Then turn the lid clockwise until it clicks into
place. Make sure that the elements are properly connect-
ed (the triangle symbol on the vessel and a symbol of a
closed padlock on the hopper must be aligned (Fig. 2g).
Incorrect installation will prevent the start of appliance.
10. Put the juice container under the juice outlet and the pulp
container under the pulp outlet (Fig. 2h).
CONTROL PANEL (FIG. 3):
To start the appliance, press the "Juicing" button on the con-
trol panel (Fig. 3, item 1).
In order to obtain mixed juice from various products, first use
the "Juicing" function (Fig. 3, item 1) with a closed cap. Then
to mix the juice, press the Mixing button (Fig. 3, item 2). The
juice in the appliance will be mixed.
To turn off the motor, press the "Stop" button (Fig. 3, item 4).
Pres and hold the "Long press to reverse" button (Fig. 3, item
3) for 2-5 seconds to reverse the rotation. Use this function
when the food products block the drive shaft or strainer.
Press the "Juicing" button (Fig. 3, item 1) to resume normal
juicing.
JUICING FUNCTION:
1. Place the prepared products in the hopper and start the
appliance by pressing the "Juicing" button on the control
panel (Fig. 3, item 1).
Note! While operating in the juicing function, juice outlet plug
must open at all times. Failure to do so will result in juice
staying in the appliance, which may lead to overflow, and
consequently to the appliance failure.
2. When the appliance is in operation, put in products of
suitable size through the inlet hole (cut larger fruits or
vegetables into smaller pieces), and press products with
the pusher. Within seconds the juice will start to flow, and
the pulp will be pushed into the pulp container through the
outlet. Do not press the product too hard with the pusher,
this may result in stopping the drive shaft.
3. If the appliance jams during operation and stops, turn it
off with the "Stop" button (Fig. 3, item 4), and then press
and hold the "Long press to reverse" (Fig. 3, item 3) for
3-5 seconds. After a complete stop of the shaft try to
restart the appliance. If necessary, repeat this process
2-3 times. If the appliance still operates improperly, turn it
off, disconnect from the mains, dismantle and remove the
products from inside the appliance.
4. When the juice vessel or pulp container is full, switch off
the appliance and empty the containers.
15
EN

Publicidad

loading

Productos relacionados para Amica JSM 4011