EINHELL TE-BS 850 E Manual De Instrucciones Original página 16

You can then connect a suitable dust extractor (a)
to the dust extractor adapter (8) (dust extractor
not supplied).
This will provide excellent dust extraction on the
workpiece.
Check that all the parts are properly connected.
Important. The vacuum cleaner you use for the
extraction work must be suitable for the workpie-
ce material.
5.1.2 Fitting the dust collection box
(Fig. 3/Item 7)
Slide the dust collection box (7) onto the connec-
tion for the dust extraction box (6). To remove the
dust collection box, proceed in reverse order.
The dust is transferred straight from the grinding/
sanding belt into the dust collection box.
To empty the dust collection box (7), open it with
the two clips (a). The top part of the dust collec-
tion box (7) can now be removed. Then clean the
dust collection box (7) thoroughly and place the
top part back in position. As you do so, make sure
that the top part is fully inserted all around and is
locked into position with the two clips (a) .
The dust collection box (7) can now be refi tted.
Important!
For health reasons it is imperative that you use
the dust collection box or a dust extraction system
via the dust extractor adapter!
5.2 Changing the grinding/sanding belt
(Fig. 4-5/Item 12)
•
Pull the clamping lever (9) outwards in order
to release the tension from the grinding/san-
ding belt.
•
Pull the worn grinding/sanding belt off the
drive rollers (11).
•
Push the new grinding/sanding belt onto the
drive rollers.
•
Make sure that the running direction of the
grinding/sanding belt (see arrow on the inside
of the grinding/sanding belt) is the same as
the running direction of the cordless belt grin-
der/sander.
•
Press the clamping lever (9) to the rear in or-
der to tension the grinding/sanding belt.
5.3 Adjusting the position of the belt
(Fig. 6/Item 10)
•
Hold the belt sander/grinder with the sanding/
grinding plate at the top.
Anl_TE-BS_850_E_SPK13.indb 16 Anl_TE-BS_850_E_SPK13.indb 16
GB
•
Switch on the belt sander/grinder.
•
By turning the setting screw (10) the belt
position should be set so that the sanding/
grinding belt is at the center of the two drive
rollers.
6. Starting up
6.1 Switching ON/OFF (Fig. 7)
To switch on:
Press the ON/OFF switch (5).
Continuous operation:
Secure the switch (5) with the locking button (4).
To switch off :
Press the ON/OFF switch (5) briefl y.
The machine can be operated on a temporary or
permanent setting.
6.2 Setting the belt speed (Fig. 8/Item 3)
You can select the belt speed by turning the set-
ting knob (3).
PLUS direction:
Increase belt speed
MINUS direction:
Reduce belt speed
6.3 Stationary use (Fig. 9-10)
You can use the belt grinder/sander in stationary
mode.
To do so, use the two clamps (13) to fasten the
belt grinder/sander on a strong and level worktop
or similar. The two fastening points (b) must be
used for this purpose.
6.4 Instructions for use
Warning! Never hold the workpiece you wish to
sand/grind in your hands. Secure the workpiece
on a sturdy surface or using a vise.
•
Allow the belt sander/grinder to start before
you place it on the workpiece.
•
Do not switch off the belt sander/grinder as
long as the sanding/grinding belt is in contact
with the workpiece.
•
Always hold the belt sander/grinder with both
hands whilst it is in use.
•
Always sand wood in the direction of the
grain.
- 16 -
06.12.2023 09:03:39 06.12.2023 09:03:39