Descargar Imprimir esta página

EINHELL TP-DW 18/225 Li Manual De Instrucciones Original página 22

Lijadora para paredes en seco inalámbrica

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 105
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.8 Battery charge level indicator (Fig. 12/
Item g)
Press the button for the battery charge level indi-
cator (h). The battery charge level indicator (g) will
indicate the charge status of the battery by means
of 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 On/Off switch (Fig. 14/Item 1)
Switching on:
Push the unlocking/locking lever (j) forward and
press the On/Off switch (1).
Locking:
With the unlocking/locking lever (j) pressed, let go
of the On/Off switch (1)
Switching off :
Press the On/Off switch (1) briefl y and then let go.
6.2 Speed controller (Fig. 14/Item 2)
You can select the speed by turning the speed
controller (2).
Plus direction: Higher speed
Minus direction: Lower speed
Anl_TP_DW_18_225_Li_SPK9.indb 22
Anl_TP_DW_18_225_Li_SPK9.indb 22
GB
6.3 Working with the drywall power sander
Place the whole surface area of the sanding
head on the material.
Switch on the machine and move it with
gentle pressure over the workpiece, making
circular or transverse and linear movements.
Use a coarse grit for coarse sanding and a
finer grit for finish sanding. You can find the
best grit size for the job by carrying out san-
ding tests.
Caution!
The dusts which are formed while the equipment
is being used may be a health hazard:
Always wear safety goggles and a dust mask
during sanding work.
All persons who work with the equipment or
enter the workplace must wear a protective
dust mask.
Eating, drinking and smoking are prohibited
at the workplace.
Paints containing lead are not allowed to be
used!
6.4 Swiveling sanding head
The sanding head can be swiveled in two axes,
enabling comfortable sanding even overhead and
in tight spaces.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
- 22 -
23.06.2021 10:39:12
23.06.2021 10:39:12

Publicidad

loading

Este manual también es adecuado para:

42.599.90