cecotec TV LED A3 ALU30043 Serie Manual De Instrucciones página 55

ENGLISH
- Do not touch or come close to the ANTENNA, SATELLITE and HDMI
terminals, and avoid electrostatic discharge while the TV is in USB and
LAN mode, otherwise the TV will stop working or show abnormal
condition.
Installing a bracket
- Call a technician to install the wall bracket. The manufacturer is not liable for damage to
property or personal injury resulting from installation by the customer.
- Make sure that the hardware used is suitable for your wall.
- Attach your TV only to a brick or concrete wall.
- Make sure that children do not hang on the TV or try to climb on it.
- VESA wall bracket is NOT INCLUDED. During installation, refer to the instructions supplied
with the wall bracket.
- 43" TV > VESA 300*300 mm
- 75" TV > VESA 400*300 mm
- 85" TV > VESA 500*200 mm
- 98" TV > VESA 800*400 mm
- The 43/75/85-inch model requires four screws to attach the wall bracket to the back of
the TV. Fig. 3
- 43" TV > M8*12 screws
- 75" TV > M6*16 screws
- 85" TV > M8*16 screws
- The 98-inch model requires six screws to attach the wall bracket to the back of the TV.
Fig. 4
- 98" TV > M8*16 screws
The figures are only a schematic diagram, please refer to the actual product.
3. OPERATION
First configuration
- Connect the power and antenna to your TV, then turn on the device.
- On first start-up, the Welcome display appears to guide you through the initial setup
process. Follow the on-screen instructions to select your preferred language, connect to
the network, perform an automatic channel search, etc.
Google - Initial Setup
When you switch on the TV for the first time, a wizard will appear to guide you through the
108 TV LED A3/ QLED V3+/ QLED V2
following initial settings:
Step 1: Select the menu language you require. Fig. 5
Note: English is recommended. The illustrations in this publication are provided for reference
only.
Step 2: (Some countries only) Select whether you want to use an Android device to set up the
TV. Fig. 6
Note
: If you do not want to use your Android device to set up the TV, skip to step 3. If you
want to use your Android device to set up the TV, activate the Bluetooth functions on your
Android phone, then search for and open the "Google" application on your phone. Follow the
instructions to configure the device.
Step 3: Select whether or not you want to connect your TV to the WLAN network. Fig. 7
Note
: If you have connected the TV to the WI-FI network, it will check for updates such as
Google service updates, etc. Then select whether you want to sign in to your Google account.
Step 4: Sign in to get new apps, recommendations, movies, Assistant and more from Google.
Fig. 8
Step 5: Please read and accept Google's terms of service and privacy policy. Fig. 9
Tv - Initial Setup
- The initial setup consists of selecting all the necessary settings to be able to scan and
store all the analogue channels that can be received.
- Make sure the TV is switched on and follow the steps below.
Note
: If the channel scan only retrieves a few channels, this could be due to poor transmission
and is therefore not covered by the manufacturer's warranty. Cecotec is not responsible for
lack of transmission or poor transmission in some areas.
- The first time you turn on the device, the initial setup wizard will open and guide you
through the initial setup process.
Step 1: Environment Fig. 10
- Press to select your environment. Then press OK to proceed to the next step.
- Home mode: You can see the standard settings for picture and sound modes.
- Shop mode: You can enjoy enhanced picture and sound mode settings.
Note
: The picture mode setting will not be accessible when selecting Store Mode.
Step 2: Where are you? Fig. 11
ENGLISH
TV LED A3/ QLED V3+/ QLED V2 109