Descargar Imprimir esta página

Scheppach C-HT570-X Traduccion Del Manual De Instrucciones Originale página 22

Cortasetos a bateria

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58
13 Disposal and recycling
Notes for packaging
The packaging materials are recy-
clable. Please dispose of packag-
ing in an environmentally friendly
manner.
Notes on the electrical and electronic equipment act
[ElektroG]
Waste electrical and electronic equipment
does not belong in household waste, but must
be collected and disposed of separately!
• Used batteries or rechargeable batteries that are not
installed permanently in the old appliance must be re-
moved non-destructively before disposal! Their dis-
posal is regulated by the battery act.
• Owners or users of electrical and electronic devices
are legally obliged to return them after use.
• The end user is responsible for deleting their personal
data from the old device being disposed of!
• The symbol of the crossed-out dustbin means that
waste electrical and electronic equipment must not be
disposed of with household waste.
• Waste electrical and electronic equipment can be
handed in free of charge at the following places:
– Public disposal or collection points (e.g. municipal
works yards)
– Points of sale of electrical appliances (stationary
and online), provided that dealers are obliged to
take them back or offer to do so voluntarily.
– Up to three waste electrical devices per type of de-
vice, with an edge length of no more than 25 centi-
metres, can be returned free of charge to the man-
ufacturer without prior purchase of a new device
from the manufacturer or taken to another autho-
rised collection point in your vicinity.
14 Troubleshooting
Fault
The product cannot be started.
Product works with interruptions. Internal loose contact.
Cutter bar becomes hot.
Poor cutting results
22 | GB
Possible cause
The battery power is too weak.
The battery is not properly inserted.
Safety switch not actuated.
On/off switch defective
Motor defective.
On/off switch defective
Cutter bar blunt.
Cutter bar has nicks.
Too much friction due to lack of lubri-
cation.
Cutter bar blunt.
Too much friction due to lack of lubri-
cation.
Dirty cutter bar.
Poor cutting technique.
www.scheppach.com
– Further supplementary take-back conditions of the
manufacturers and distributors can be obtained
from the respective customer service.
• If the manufacturer delivers a new electrical appliance
to a private household, the manufacturer can arrange
for the free collection of the old electrical appliance
upon request from the end user. Please contact the
manufacturer's customer service for this.
• These statements only apply to devices installed and
sold in the countries of the European Union and which
are subject to the European Directive 2012/19/EU. In
countries outside the European Union, different regu-
lations may apply to the disposal of waste electrical
and electronic equipment.
Notes on lithium-ion batteries
Remove the battery before disposing of the de-
vice!
• Do not dispose of the battery in household waste, in a
fire (risk of explosion) or in water. Damaged batteries
can harm the environment and your health if toxic va-
pours or liquids escape.
• Defective or used batteries must be recycled in accor-
dance with Directive 2006/66/EC.
• Hand in the device and the battery charger at a recy-
cling centre. The plastic and metal parts used can be
separated by type and thus recycled.
• Dispose of batteries when discharged. We recom-
mend covering the poles with an adhesive strip to pro-
tect against a short circuit. Do not open the battery.
• Dispose of batteries according to local regulations.
Return batteries to a used battery collection point
where they can be recycled in an environmentally
friendly manner. Ask your local waste disposal com-
pany about this.
Remedy
Charge the battery.
Push the battery into the battery mount. The
battery clicks into place audibly.
Switch the product on.
Please contact our service department.
Please contact our service department.
Check cutter bar, sharpen or contact our service
department.
Oil the cutter bar.
Check cutter bar, sharpen or contact our service
department.
Oil the cutter bar.
Clean the cutter bar.
Observe the working instructions.

Publicidad

loading

Este manual también es adecuado para:

5910607900