Operating Instructions; Remote Handset - Truma Mover S Instrucciones De Uso

Ocultar thumbs Ver también para Mover S:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 64

Operating instructions

Remote handset

a = On / Off slide switch
I
On (green LED illuminates)
£ Off (green LED goes off)
b = Caravan forwards (both wheels
rotate in forwards direction)
c = Caravan reverse (both wheels
rotate in reverse direction)
d = Caravan right forwards
(left wheel rotates in forwards
direction)
e = Caravan left forwards
(right wheel rotates in forwards
direction)
f = Caravan right reverse (left wheel
rotates in reverse direction)
g = Caravan left reverse (right wheel
rotates in reverse direction)
Mover SE R only
The caravan can be turned in a circle on the spot without
moving forward.
d + g = Turn caravan to the right
(left wheel rotates forwards + right wheel rotates
backwards)
e + f = Turn caravan to the left
(left wheel rotates backwards + right wheel rotates
forwards)
Mover TE R only
Turning on the spot without moving forward is not possible
because of the two axles. Pressing the d, g, e or f buttons
causes the Mover to move in a circle, whereby the outer
motor runs continuously and the inner motor pulsates.
Mover SE R / TE R
h = Two-hand operation, engage drive rollers
i = Two-hand operation, disengage drive rollers
Both buttons must always be pressed simultaneously to
engage or disengage the drive rollers.
The engaging or disengaging starts after about 3 seconds
(safety delay). The drive rollers automatically move to the end
position, even if both buttons are released.
Pressing the two buttons for disengaging whilst the
Mover is engaging in causes the engaging procedure to
be aborted. The drive rollers will disengage and automatically
move to the end position.
The remote hand set switches off:
– after approx. 2 minutes, if no button is pressed
– after approx. 7 minutes, if one of the movement buttons is
permanently held down. The green LED goes off.
To reactivate the remote control, move slide switch to "Off" £
and then back to "On" I after approximately 1 second.
There is no "On / Off" switch on the caravan to be operated.
14
Remote hand set LED flash codes and
acoustic signal
LED "On" and no acoustic signal
System is ready for operation
LED "Off" and no acoustic signal
System off
(check remote hand set batteries if necessary)
LED "flashes" in combination with acoustic signal
– for approx. 5 seconds after switching the remote hand set
on, until the system is ready for operation.
– for approx. 10 seconds after switching the remote hand set
on, then it is switched off again – 13-pin safety plug not
connected to safety socket or unable to establish radio link
to controller.
– every 3 seconds if the caravan battery has a low charge
(finish manoeuvring as quickly as possible and charge
battery).
– 5 times a second (5 Hz) if the caravan battery voltage is
low. No manoeuvring is possible until the battery voltage is
above 11 V again (e.g. by means of recovery / battery charg-
ing). The drive rollers can also be disengaged with a voltage
of less than 11 V.
– approx. 2 times per second with overcurrent / over-
temperature (2 Hz). Switch remote hand set off and on
again (wait for cooling down if necessary in the event of
overtemperature).
Changing the batteries in the remote handset
Please be sure to use leak proof micro-
batteries only, type LR 03, AAA, AM 4,
MN 2400 (1.5 V).
When fitting new batteries
ensure the polarity is correct!
Dead and used batteries may
leak and damage the remote
handset! Remove the batteries if the
handset is not going to be used for an
extended period.
No claims under guarantee will be considered for damage
caused by leaking batteries.
Before throwing away a defective handset, it is essential that
the batteries are removed and disposed of in proper manner.

Hide quick links:

Publicidad

Tabla de contenido
loading

Tabla de contenido