Makita DGA417 Manual De Instrucciones página 20

For model other than 100 mm (4")
► Fig.17: 1. Sanding lock nut 2. Abrasive disc
3. Rubber pad
1. Mount the rubber pad onto the spindle.
2.
Fit the disc on the rubber pad and screw the sand-
ing lock nut onto the spindle.
3. Hold the spindle with the shaft lock, and securely tighten
the sanding lock nut clockwise with the lock nut wrench.
To remove the disc, follow the installation procedure in
reverse.
Installing or removing Ezynut
Optional accessory
Only for tools with M14 spindle thread.
Mount inner flange, abrasive wheel and Ezynut onto the
spindle so that Makita Logo on Ezynut faces outside.
► Fig.18: 1. Ezynut 2. Abrasive wheel 3. Inner flange
4. Spindle
Press shaft lock firmly and tighten Ezynut by turning the
abrasive wheel clockwise as far as it turns.
► Fig.19: 1. Shaft lock
To loosen the Ezynut, turn the outside ring of Ezynut
counterclockwise.
NOTE: Ezynut can be loosened by hand as long
as the arrow points the notch. Otherwise a lock nut
wrench is required to loosen it. Insert one pin of the
wrench into a hole and turn Ezynut counterclockwise.
► Fig.20: 1. Arrow 2. Notch
► Fig.21
Installing abrasive cut-off / diamond wheel
Optional accessory
WARNING:
When using an abrasive cut-off
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
WARNING:
NEVER use cut-off wheel for side
grinding.
► Fig.22: 1. Lock nut 2. Abrasive cut-off wheel / dia-
mond wheel 3. Inner flange 4. Wheel guard
for abrasive cut-off wheel / diamond wheel
As for the installation, follow the instructions for
depressed center wheel.
The direction for mounting the lock nut and the inner
flange varies by wheel type and thickness.
Refer to the following figures.
For 100 mm (4") model
When installing the abrasive cut-off wheel:
► Fig.23: 1. Lock nut 2. Abrasive cut-off wheel
(Thinner than 4 mm (5/32")) 3. Abrasive cut-
off wheel (4 mm (5/32") or thicker) 4. Inner
flange
When installing the diamond wheel:
► Fig.24: 1. Lock nut 2. Diamond wheel (Thinner than
4 mm (5/32")) 3. Diamond wheel (4 mm
(5/32") or thicker) 4. Inner flange
For model other than 100 mm (4")
When installing the abrasive cut-off wheel:
► Fig.25: 1. Lock nut 2. Abrasive cut-off wheel
(Thinner than 4 mm (5/32")) 3. Abrasive cut-
off wheel (4 mm (5/32") or thicker) 4. Inner
flange
When installing the diamond wheel:
► Fig.26: 1. Lock nut 2. Diamond wheel (Thinner than
4 mm (5/32")) 3. Diamond wheel (4 mm
(5/32") or thicker) 4. Inner flange
Installing wire cup brush
Optional accessory
CAUTION:
Do not use brush that is damaged,
or which is out of balance. Use of damaged brush
could increase potential for injury from contact with
broken brush wires.
Place the tool upside down to allow easy access to the
spindle.
Remove any accessories on spindle. Thread wire cup
brush onto spindle and tighten with supplied wrench.
► Fig.27: 1. Wire cup brush
Installing wire wheel brush
Optional accessory
CAUTION:
Do not use wire wheel brush that
is damaged, or which is out of balance. Use of
damaged wire wheel brush could increase potential
for injury from contact with broken wires.
CAUTION:
ALWAYS use guard with wire
wheel brushes, assuring diameter of wheel fits
inside guard. Wheel can shatter during use and
guard helps to reduce chances of personal injury.
Place the tool upside down to allow easy access to the
spindle.
Remove any accessories on spindle. Thread wire wheel
brush onto spindle and tighten with the wrenches.
► Fig.28: 1. Wire wheel brush
Installing hole cutter
Optional accessory
Place the tool upside down to allow easy access to the
spindle.
Remove any accessories on the spindle. Thread the
hole cutter onto the spindle, and tighten it with the sup-
plied wrench.
► Fig.29: 1. Hole cutter
20 ENGLISH