Pressure Washer Rinsing - Craftsman 580.752070 Instrucciones De Uso

7. Make sure garden h ose is connected towater i nlet.
Check thathigh pressure hose isconnected tospray gun
and pump. Turn onwater.
You must attach alI hoses before
Starti_gthe enginewithoutall the hosesconnected andwithout
the waterturnedONwill damage the pump.
Darnage to eqdpmentresultingfrom failureto follow this
instructionwill void warranty.
8. Engagetrigger iock on spray gun and start engine
foiiowing instructions How to Start Your Pressure
Washer.
9£ If using cteaning tank, rotate detergent shut-off valve on
cleaning tank to "On" position (A).
/
f
IMPORTANT:If using detergent siphoning hose, make sure
detergent shut-off valve ell cleaning tank is in the "Off"
position.
9B. If using detergent siphoning hose, placesmall filter end
of detergent siphoning tube into detergent container.
NOTE:Make sure the filter is fully submerged in detergent
while applying detergent.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
Wheninsqting the filter into a detergent s olutionbottle,route
the tubeso asto keepit from inadvertently' contacting the hot
rnuffler.
10. Appiy HydroFoam
TM
wash to a dry surface, starting at
lower portion of area to be washed and work upward,
using iong, even, overlapping strokes.
NOTE:To prevent water spotting on vehicles, work in a
shaded area and allow surfaces to coot before beginning.
11. Allow HydroFoam
TM
wash to soak in between
3-5 minutes before washing and rinsing. Reappiy as
needed to prevent surface from drying. DO NOTailow
HydroFoam
TM
wash to dry on (prevents streaking).
For best resuits, scrub the HydroFoam
TM
wash covered
surface to heip remove stubborn dirt, grime and stains. For
vehicles, use a soft car wash brush or mitt. For decking,
siding and concrete, use a brush appropriate for the type of
surface being cleaned.
IMPORTANT:When using the detergent siphoning hose, you
must flush the detergent siphoning system after ea@ use by
placing the fiiter into a bucket of clean water, then run the
pressure washer in low pressure for 1-2 minutes.
Pressure Washer Rinsing
AfterNydroFoam
TM
wash is applied, s¢onrthe surfane and rinse
it deae as fdbwn:
1. Engagetrigger lock on spray gun.
2. Make sure detergent shut=off vaive is in "Off" position.
3. Remove HyrdoFoam
TM
Launcherfrom nozzteextension.
4. Seiect and instaii desired ProjectPro@nozzle,as
described in How to Use ProjectPm@ NozzleSystem.
5. Keepspray gun a safe distance from spray surface.
WARNING
Kickback from spray gun can cause you to fail.
6.
* Operate pressure washerfrom a stablesurface.
, Beextremely carefulif you mustusethe pressure washerfrom
a ladder,scaffolding,or anyothersimilarlocation.
o Firmlygraspspraygun with both handswhenusing high
pressure sprayto avoidinpry whenspraygun kicks back.
Apply a high pressure spray to a small area and then
check the surface for damage. If no damage, proceed to
step 7.
Start at top of area to be rinsed, working down with
same overlapping strokes used for cleaning.
Autemati¢ Cod Dewu System (Thermal Relief}
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engagesto cool the pump by discharging
the warm water onto the grennd.
15