Publicidad
Idiomas disponibles
Idiomas disponibles
area first and then in the other. NOTE: For best results, wind line onto the outer
a. Your line spool for this product has two (2) wind areas for line. Wind line in one
portion of the spool (side with arrows) first.
in Figure 13. Insert the hooked end of the line into the slot on the inside of the
b. Fold over nylon line about 3/4" (19mm) from the end to form a "hook" as shown
spool.
c. Snugly and evenly wind the bulk line onto the spool in the direction of the arrow
on the spool until the line builds up to the notches in the spool rim. Do not overfill
spool. Repeat for the other wind area.
Figure 10.
4. Place spool and line into spool housing with lines "parked" in slots provided as shown in
pulls out of the holding slots as shown in Figure 11.
5. Insert the line ends through the holes in the spool hub. Pull slack line through until it
6. Press the spool down GENTLY and rotate it until you feel it drop into place and then
push to snap into place. (When in place, the spool will turn a few degrees left and right
7. Snap the hub cap back on as shown in Figure 12, by depressing lugs and pressing into
freely). Take care to keep the line from becoming trapped under the spool.
spool housing. NOTE: Make sure that cover is fully positioned, listen for two audible
clicks to ensure both lugs are correctly located. Power the tool on. In a few seconds or
less you'll hear the nylon line being cut automatically to the proper length.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
ACCESSORIES
Use Black & Decker replacement spool Model No. DF-080.
Reload nylon line (either bulk or prewound replacement spool) as shown in this manual.
• USE ONLY .080" (2mm) DIAMETER NYLON MONOFILAMENT LINE. Do not use
serrated or heavier gauge line, as they will overload the motor and cause overheating.
The unit only functions properly with 0.080" (2mm) diameter nylon monofilament line. This
line is available at your local dealer or authorized service center.
WARNING: The use of any accessory not recommended by Black & Decker for use with
this tool could be hazardous.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations.
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you.
Para reparación y servicio de sus herramientas eléctricas, favor de dirigirse
Solamente para propósitos de Mexico:
al Centro de Servicio más cercano:
CULIACAN, SIN
MONTERREY, N.L.
Av. Nicolás Bravo #1063 Sur
Av. Francisco I. Madero
(667) 7 12 42 11
No.831
Col. Industrial Bravo
(81) 8375 2313
GUADALAJARA, JAL
Col. Centro
PUEBLA, PUE
Av. La Paz #1779
(33) 3825 6978
17 Norte #205
Col. Americana Sector Juarez
(222) 246 3714
MEXICO, D.F.
Col. Centro
QUERETARO, QRO
Eje Central Lázaro Cardenas
No. 18
Av. Madero 139 Pte.
(55) 5588 9377
(442) 214 1660
Local D, Col. Obrera
Col. Centro
MERIDA, YUC
SAN LUIS POTOSI, SLP
Calle 63 #459-A
Av. Universidad 1525
(999) 928 5038
(444) 814 2383
PARA OTRAS LOCALIDADES LLAME AL: (55) 5326 7100
Col. Centro
Col. San Luis
Vea "Herramientas
eléctricas (Tools-Electric)"
– Páginas amarillas –
para Servicio y ventas
ESPECIFICACIONES/ESPECIFICAÇÕES/SPECIFICATIONS
GH1000
AR
Voltaje/Voltagem/Votlage
220V
Frecuencia/Frequency
50Hz
Potencia/Power
900W
RPM
7,200
Solamente para propósito de Argentina:
Importado por: Black & Decker Argentina S.A.
Pacheco Trade Center
Colectora Este de Ruta Panamericana
Km. 32.0 El Talar de Pacheco
Partido de Tigre
Buenos Aires (B1618FBQ)
República de Argentina
No. de Importador: 1146/66
Tel. (011) 4726-4400
Imported by/Importado por:
Black & Decker do Brasil Ltda.
Rod. BR 050, s/n° - Km 167
Dist. Industrial II
Uberaba ˆ MG ˆ Cep: 38064-750
CNPJ: 53.296.273/0001-91
Insc. Est.: 701.948.711.00-98
S.A.C.: 0800-703-4644
Solamente para propósitos de CCA
Importado por: Black & Decker LLC
Calle Miguel Brostella Final
Edificio Milano I, Mezanine 5,6 y 7
El Dorado, Panama
Tel. 507-360.5700
188062-00
07/23/07
TORREON, COAH
Blvd. Independencia, 96 Pte.
(871) 716 5265
VERACRUZ, VER
Col. Centro
Prolongación Díaz Mirón #4280
(229)921 7016
VILLAHERMOSA, TAB
Col. Remes
Constitución 516-A
(993) 312 5111
Col. Centro
BLACK & DECKER S.A. DE C.V.
BOSQUES DE CIDROS ACCESO RADIATAS NO. 42
COL. BOSQUES DE LAS LOMAS.
05120 MÉXICO, D.F
TEL. 55-5326-7100
B2
B3
B2C
220V
120V
220V
60Hz
60Hz
50Hz
900W
900W
900W
7,200
7,200
7,200
Solamente para propósitos de Colombia
Importado por: Black & Decker de Colombia, S.A.
Carrera 85D # 51-65, Bodega 23
Complejo Logístico San Cayetano
Bogota - Colombia
Tel. 744-7100
Solamente para propósito de Chile:
Importado por: Black & Decker de Chile, S.A.
Av. Pdte. Eduardo Frei M. 6001-67 Conchalí
Santiago de Chile
Tel. (56-2) 687 1700
Solamente para propósito de México:
Importado por: Black & Decker S.A. de C.V.
Bosques de Cidros, Acceso Radiatas No.42
3a. Sección de Bosques de las Lomas
Delegación Cuajimalpa,
05120, México, D.F.
Tel. (52) 555-326-7100
R.F.C.: BDE810626-1W7
Black & Decker del Perú S.A.
Av. Enrique Meiggs 227. Pque. Industrial - Callao
Teléfono: (511) 452-5577
RUC 20266596805
BR
127V
60Hz
900W
7,200
Publicidad
