Descargar Imprimir esta página

Bosch PR20EVS Instrucciones De Funcionamiento Y Seguridad página 17

Publicidad

Idiomas disponibles

Idiomas disponibles

BM 2610021461 06-12_BM 2610021461 06-12.qxp 6/26/12 1:38 PM Page 16
PR009 AND PR010 ROUND SUBBASES &
USE OF TEMPLET GUIDE BUSHINGS WITH
PR001 FIXED BASE
(Available as optional accessories)
Optional large round subbases are available
separately and allow various templet guide
bushings to be used with the palm routers.
Templet guide bushings are used to guide the
router to repeatedly make consistent openings
and inlays using various templets (also referred to
as patterns and jigs). Templets for standard
routing applications are available commercially,
such as the Bosch hinge templet kit; and templets
for specialty applications are typically made by
users for their specific needs.
The PR009 Round Subbase accepts the Bosch
RA-Series Templet Guide Adapters.
The PR010 Round Subbase accepts threaded
templet guide adapters.*
*Note: The RA1100 Adapter for Threaded
Templets allows use of conventional threaded
templet guides with the PR009 Round Subbase.
PR009 Attachment of Templet Guide and
Round Subbase (Fig. 19)
1. Remove regular subbase.
2. Insert templet guide into top of round subbase
such that the anti-rotation stops in the subbase
fit into the corresponding places in the templet
guide. (When using the RA1100 adapter, first
place the rubber O-ring between the anti-
rotation stops and the subbase.) (Fig. 20).
3. Loosely attach round subbase using panhead
screws that come with that accessory.
4. Center the templet guide around the bit. (The
optional Bosch RA1150 Centering Cone can
be used to ensure that the templet guide is
properly centered.)**
5. Tighten the panhead screws to hold the
templet guide and subbase in position.
Note: If a templet guide seems loose, repeat
steps 2- 5 after adding the rubber O-ring.
PR010 Attachment Round Subbase of
Threaded Templet Guide (Fig. 21)
1. Remove regular subbase.
2. Loosely attach round subbase using panhead
screws that come with that accessory.
3. Attach the threaded templet guide by putting
the templet guide through the bottom and
attaching the ring from the top.
4. Center the templet guide around the bit. (The
optional Bosch RA1151 Centering device can
be used to ensure that the templet guide is
properly centered.)**
RUBBER O-RING
FIG. 19
(If necessary)
PANHEAD
SCREWS
FIG. 20
ANTI-
ROTATION
STOPS
FIG. 21
TEMPLET
GUIDE
PANHEAD
SCREWS
FIG. 22
ROUTER BIT
OFFSET
5. Tighten the panhead screws to hold the
templet guide and subbase in position.
Creating Templets
Templet patterns can be made of plywood,
hardboard, metal or even plastic. The design can
be cut with a router, jigsaw, or other suitable
cutting tool. Remember that the pattern will have
to be made to compensate for the distance
between the router bit and the templet guide (the
"offset"), as the final workpiece will differ in size
from the templet pattern by that amount, due to
the bit position (Fig. 22).
*See page 26 for available templet guide sizes.
**See page 25 for details about centering.
-16-
TEMPLET
ROUTER
GUIDE
BASE
PR009 SUBBASE
RUBBER O-RING
(If necessary)
ANTI-
ROTATION
STOPS
ROUTER BASE
TEMPLET GUIDE
RING
PR010 SUBBASE
COLLET CHUCK
ROUTER
TEMPLET
SUBBASE
GUIDE
TEMPLET
PATTERN
WORKPIECE

Publicidad

loading

Este manual también es adecuado para:

Pr20ePr10e