Operating Procedures - Hitachi Koki Tanaka TCS 33EDTP Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATING PROCEDURES

Fuel (Fig. 8)
WARNING
○ Do not use fuel with more than 10%
ethanol in this unit.
Use of fuel, such as E15 (15% ethanol), E20
(20% ethanol), E85 (85% ethanol), may
cause problems including overheating,
premature deterioration of fuel lines and carburetors.
Use of fuel with more than 10% ethanol may result
in personal injury or property damage.
Use of fuel with more than 10% ethanol will void the
product warranty.
Check the ethanol level before purchasing fuel for
this unit.
○ The chain saw is equipped with a two-stroke engine.
Always run the engine on fuel, which is mixed
with oil. Provide good ventilation, when fueling or
handling fuel.
○ Fuel contains highly fl ammable and it is possible
to get the serious personal injury when inhaling or
spilling on your body. Always pay attention when
handling fuel. Always have good ventilation when
handling fuel inside building.
Fuel
○ Always use branded 89 octane unleaded gasoline.
○ Use genuine two-cycle oil or use a mix between 25:1
to 50:1, please consult the oil bottle for the ratio or
Tanaka dealer.
○ Only for the state of California at 50:1.
○ If genuine oil is not available, use an anti-oxidant
added quality oil expressly labeled for air-cooled
2-cycle engine use (JASO FC GRADE OIL or ISO
EGC GRADE). Do not use BIA or TCW (2-stroke
water-cooling type) mixed oil.
○ Never use multi-grade oil (10 W/30) or waste oil.
○ Always mix fuel and oil in a separate clean container.
Always start by fi lling half the amount of gasoline, which
is to be used.
Then add the whole amount of oil. Mix (shake) the fuel
mixture. Add the remaining amount of gasoline.
Mix (shake) the fuel-mix thoroughly before fi lling the
fuel tank.
Fig. 8
Fueling
WARNING (Fig. 9)
○ Always shut off the engine and let it cool for a few
minutes before refueling.
○ Do not smoke or bring fl ames or sparks near the
fueling site.
○ Slowly open the fuel tank (13), when fi lling up with
fuel, so that possible overpressure disappears.
○ Tighten the fuel tank cap carefully, after fueling.
○ Always move the unit at least 10 feet (3 m) from the
fueling area before starting.
○ Always wash any spilled fuel from clothing
immediately with soap.
○ Be sure to check any fuel leaking after refueling.
13
Before fueling, clean the tank cap area carefully, to
ensure that no dirt falls into the tank. Make sure that
the fuel is well mixed by shaking the container, before
fueling.
Mixing amount of two-cycle oil and gasoline
Gasoline
US gallon (Liter)
1 (3.8L)
2 (7.6L)
5.2 (152 ml) - 10.4 (304 ml)
5 (19L)
Chain oil (Fig. 9)
WARNING
Never use waste or regenerated oil. If you use them,
it will cause damage to your health or this unit.
Slowly open the oil tank (14), and fi ll up with chain oil.
Always use good quality chain oil. When the engine is
running, the chain oil is automatically discharged.
Fill up the oil tank (14) with chain oil every time when
refueling.
NOTE
When pouring fuel (13) or chain oil (14) into the tank,
place the unit with cap side up. (Fig. 9)
English
14
Fig. 9
Two-cycle oil
US fl .oz (ml)
Ratio 50:1
Ratio 25:1
2.6 (76 ml) - 5.2 (152 ml)
13 (380 ml) - 26 (760 ml)
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Cs 33edtp

Tabla de contenido