Descargar Imprimir esta página

Black and Decker NVD215J Traducción De Las Instrucciones De Manejo Originales página 15

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17
Charging the Battery (Fig. B)

WARNING:
supplied charger.

WARNING:
ambient temperatures below 4 °C or above 40 °C.
From new, the rechargeable cells of the product need a minimum
charge time of 5 hours to ensure full power.
1. The trigger
1
must be in the OFF position, the appliance
will not charge if it is in any other position.
2. Fig. B - Plug the jack plug 
charging port 
of the tool.
 5 
3. Plug the charger into any standard 240V (NVD215J)
electrical outlet.
4. The charge indicator LED 
housing will illuminate while charging.
5. The charge indicator LED will turn off upon completion
of charging.
nOTE: While charging, the charger may get warm, this is
perfectly normal and safe. It is safe to leave the appliance
connected to the charger indefinitely. The charger
automatically reduces power consumption when charging
is complete.

WARNING:
ambient temperatures below 4 °C or above 40 °C.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and keep away from the trigger
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only the supplied BLACK+DECKER charger.
Switching On (Fig. E)
1. To switch the appliance ON, press and hold the On/Off
trigger
1
on the underside of the handle
2. To turn the appliance OFF, release the trigger.
Dry Pick Up
For everyday spills of dry material.
Do not fill the dust bowl
intake chute.
Optimizing the Suction Force
In order to keep the suction force optimized, the filters must be
cleared regularly during use.
For use only with the
Do not charge the battery at
 7 
of the charger
6
into the
on the center of the main
 8 
Do not charge the battery at
2
.
beyond the end of the
3
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and keep away from the trigger
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only the supplied BLACK+DECKER charger.
Dust Bowl (Fig. F)

WARNING: Never use this cordless hand vacuum without
its filters.
IMPORTanT: Maximum dust collection will only be obtained
with clean filters and an empty dust bowl. If dust begins to fall
back out of the product after it is switched off, this indicates that
the dust bowl is full and requires emptying
To Empty the Dust Bowl (Fig. F)
1. Place the dust bowl over a trash bin and remove the dust
bowl 
 3 
from the main housing 
bowl counterclockwise and pulling the dust bowl away from
the main housing.
2. Remove the filter assembly by pulling it out of the
dust bowl.
3. Shake or lightly brush any dust from the filter assembly.
4. Empty the dust from the dust bowl into a trash bin and
wash if necessary. Ensure that the dust bowl is completely
dry before using.
5. Place filter assembly into position in the dust bowl.
6. Install the dust bowl onto the main housing, ensuring the
dust bowl slots 
 13 
align with the main housing tabs 
shown in Fig. F and rotate the dust bowl clockwise to lock it
firmly into position.
Cleaning the Filters (Fig. G)
1. Place the dust bowl over a trash bin and remove the dust
bowl 
from the main housing 
 3 
bowl counterclockwise and pulling the dust bowl away from
the main housing.
2. Remove the filter assembly by pulling it out of the
dust bowl.
3. Empty any dust from the dust bowl into a trash bin and
wash if necessary. Ensure the dust bowl is completely dry
before using.
4. Twist the pre-filter
 15 
pre-filter off of the filter 
dust from the filter and pre-filter.
5. Wash the pre-filter and filter regularly using warm, soapy water.
The cleaner the filter is, the better the product will perform.
6. Ensure both filters are completely dry for 12 hours
before refitting. It is very important that the filters are
completely dry and correctly in position before use.
7. Install the pre-filter onto the filter, ensuring the filter
slots 
 17 
align with the pre-filter tabs 
pre-filter clockwise to lock it firmly into position.
8. Install the filter assembly into the dust bowl.
EnGLIsh
 12 
by twisting the dust
by twisting the dust
 12 
counterclockwise and pull the
 16 
. Shake or lightly brush any
 18 
and rotate the
 14 
as
13

Publicidad

loading