Overhead Rigging - JB Systems Light LED DJ-BAR Manual De Instrucciones

ENGLISH

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
BUILDING TOGETHER AND INSTALLING ON A LIGHT STAND:
 Unpack all parts and put them on a table.
 Push the following parts in the correct order in the sliding section (B)
located on the bottom of the 4BAR:
 Bolt (A) for LED panel1
 Bolt (A) for LED panel2
 Nut for 35mm Adapter (H)
 Bolt (A) for LED panel3
 Bolt (A) for LED panel4
 Refer to the drawing to see how the 4 panels should be fixed correctly:
 First add the leather washer (C)
 Add the metal washer (D)
 Add the LED PANEL (F)  Important: the connector should be on
the same side as the LED power signal cable (G) of the 4bar.
 Add the black knob (E) and fasten well.
 Insert the LED power cable (G) in the back of the four corresponding
panels.
 When the 4 panels are fixed to the 4bar, you can install the 35mm adapter
(I)  simply turn the thread of the adapter in the nut (H) (nut already in
place) until it is well tightened.
 Open the knob of the adapter (J) and put the assembled
LED DJ-BAR on top of a stable light stand.
 Tighten the knob of the adapter (J) and connect all cables
(see later)
 You can still align the panels in different directions.
 Done!
JB SYSTEMS
®
OPERATION MANUAL
3/77 LED DJ-BAR
ENGLISH
DESCRIPTION:
1. Mains input with IEC socket and integrated fuse holder, connect the supplied mains cable here.
2. DMX input
3. DMX output
4. ¼" Jack input for the optional CA-8 hand controller
5. Internal microphone
6. Slave LED: is lit when the unit is in slave mode
7. Sound LED: blinks to the rhythm of the music while the unit is in audio mode
8. DMX LED: is lit when the unit receives a DMX-signal
9. Master LED: is lit when the unit is switched as master
10. MENU button: used to select the different menu items
11. DOWN button: to go back in the menu and to lower the values shown on the display.
12. UP button: to go up in the menu and to increase the values shown on the display.
13. ENTER button: used to confirm your choice.
14. DISPLAY shows the various menus and the selected functions.
15. 35mm STAND ADAPTER: used to put the LED 4Bar easily on top of a light stand
16. Special cables with LED power signal for the passive LED panels
17. Passive LED panels
HOW TO SETUP:
MAIN MENU:
 To select any of the menu options, press the MENU button up to when the required option is shown on the
display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to choose the desired menu option.
 Once the required menu option is selected, press the ENTER button to select. To go back to the functions
without any change press the MENU button for about 2 seconds or just wait 8 seconds. The menu
structure is shown below.
JB SYSTEMS
®
OPERATION MANUAL
4/77 LED DJ-BAR