Publicidad
Idiomas disponibles
Idiomas disponibles
external timer or a remote control system.
The manufacturers decline any responsibility
in the event of non-compliance with what is
described above and the accident prevention
norms not being respected and followed.
To avoid all risk, if the power cable becomes
damaged, it must only be replaced by the
manufacturer, by an authorised service centre,
or by a qualified electrician.
OPERATING PRINCIPLE (Fig. 1)
It exploits the electromagnetic properties of most cooking vessels.
The coil (inductor) which produces the electromagnetic field is
operated and controlled by the electronic circuit.
The heat is transmitted to food by the cooking vessel itself.
The cooking process takes place as described below.
- loss of heat is minimum (high efficiency)
- the system stops automatically when the vessel is removed or even
just lifted from the hob
- the electronic circuit guarantees maximum flexibility and fine
adjustments.
(Fig. 1)
1 Vessel
2 Induced current
3 Magnetic field
4 Inductor
5 Electronic circuit
6 Power supply
User's Instructions (Fig. 2)
1 Power ON / Power OFF
2 Slider sensor
3 Power key
4 Lock key
5 ON/OFF LED
6 Slider LED
7 Lock LED
8 Heating zone and setting display
9 Timer indicator zone
10 Timer
Installation
All operations relative to installation (electric connection) should be
carried out by skilled personnel in conformity with the rules in force.
As for the specific instructions see part pertaining to installer.
Functionality Slider TC:
Slider: sensor technology of the novel Slider TC allows as well an
adjustment of the cooking levels (1 – 9) as the timer value (1- 99) by
touching and pulling the finger over the designated area.
Pulling to the right is increasing and to the left is decreasing
accordant value.
Moreover a direct selection of the designated value is also possible
on the slider area.
ON/OFF Touch Control
After connecting to the mains the TC unit takes 1 second to prepare
for operation. After a reset all displays and LEDs flashes up for 1
second. After 1 second all displays and LEDs are switched off again.
The TC unit may now be switched ON by pressing the ON/OFF key "1".
Displays show a steady "0". Possible optic warnings for hot cooking
zones [H] are displayed in alternation with [0] and the synchronously
display dot. The display dots on the cook top displays flashes up
every second (0.5 sec.off, 0.5 sec. on).
Electronics remains activated for 20 seconds. If there is no
cooking level or timer selection done in this period the electronics
automatically resets to the Off-mode by releasing a signal tone.
The TC may only be switched on by pressing the power key as sole
input In case of an other key is pressed (single or in parallel with the
power key), the control unit is not switched on.
In case of an active "Child Lock Function" when switching POWER ON,
all cooking zone displays show "L" for LOCKED .
Possible optic warnings for hot cooking zones [H] are displayed in
alternation with [L] (H-ON= 0.5 sec; L-ON = 1.5sec).
By pressing the ON/OFF key "1" of the control unit in ON-Mode, the
Touch Control may be switched off at any time. This is also applicable
for locked control units (active child lock). The ON/OFF key takes
always priority with the POWER-OFF function.
Automatic Switch Off
The TC switches from Power ON to OFF after 20 sec., provided that no
cooking zone is activated or a select key is pressed during that time.
In case of a selected cooking zone (with cooking stage is "0") this
Auto Power off time is composed of a 10 sec deselection time and 10
sec Power off time.
ON/OFF Cooking Zone
In case of On-state of the TC a cooking zone may be selected by
touching the dedicated display (Select-Sensors "8"). The respective
display changes to a steady display dot and "0" instead of "H" – in
case of a hot cooking zone-. On all other cooking zone displays the
dot expires.
That followed a cooking level may be set by using the Slider area.
Thus switches the respective cooking zone on. End stops are „9"
(right side) and „0" (left side).
First place the pan in the chosen cooking zone. If the pan is not
present the system cannot be switched on the correspondent zone.
Switching Off a single cooking zone:
A single cooking zone may be switched off by selecting and setting
cooking level to [0]. In case of an optic warning for hot cooking zones
[H] this is displayed in alternation with [0] and the synchronously
display dot.
After the TC is switched Off the display remains black respectively [H]
is displayed for an optic warning for hot cooking zone.
Switching Off all cooking zones:
Immediately switching off all cooking zones is always possible by
using the ON/OFF key.[H] possibly appears on all hot cooking zones .
All other cooking zone displays remain black.
Power Stages
The power of the cooking zone is adjustable in 9 different stages; the
respective stage is displayed ([1"] to [9]) via LEDseven- segment-displays.
Publicidad
