Publicidad
SkyAir RZAC Series
15. Accessories
15.1 Indoor Unit
15.1.1 FCA
Optional accessories
Standard panel with sensing sensor
Decoration
Standard panel
panel
Designer panel (Note 1)
Auto grille panel (Note 2, 3)
Sealing material of air discharge outlet (Note 4)
Panel spacer
Fresh air intake kit
High-efficiency filter unit (Note 8)
(including filter chamber)
Replacement high-efficiency filter (Note 8, 9)
Filter chamber
Replacement long-life filter
Replacement long-life filter (auto grille panel)
Ultra long-life filter unit (including filter chamber) (Note 8)
Replacement ultra long-life filter (Note 8, 9)
Branch duct chamber (Note 4)
Insulation kit for high humidity (Note 8, 10)
Remote controller
Navigation remote controller
Simplified remote controller
Central remote controller (Note 11)
Unified ON/OFF controller (Note 11)
Schedule timer (Note 11)
intelligent Touch Controller (Note 11)
Adaptor for wiring (Note 12)
Wiring adaptor for electrical appendices (Note 12)
Installation box for adaptor PCB
Remote sensor (for indoor temperature)
Note:
1. When installing designer panel, body height (ceiling required dimension) is 42 mm higher than standard panel. Designer panel cannot operate
2 and 3 way flow.
2. A dedicated remote controller (BRC16A2) for the auto grille panel is included for lowering and raising the suction grille.
3. When installing auto grille panel, body height (ceiling required dimension) is 55 mm higher than standard panel.
4. Circulation airflow is not available with this option.
5. When installing a fresh air intake kit (chamber type), two air outlet corners are closed.
6. It is recommended that the volume of outdoor air introduced through the kit is limited to 10% of the maximum airflow rate of the indoor unit.
Introducing higher quantities will increase the operating sound and may also influence temperature sensing.
7. The volume of fresh air for direct installation type is approximately 1% of the indoor unit airflow. The chamber type is recommended when
more fresh air is necessary.
8. This option cannot be installed to designer panel and auto grille panel.
9. Filter chamber is required.
10. Please use in case temperature/humidity inside ceiling may get over 30°C, 80% RH.
11. The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
12. Installation box for adaptor PCB (KRP1H98A) is necessary.
13. Please order using the names of both components instead of set name.
14. Wiring for wired remote controller should be obtained locally.
Item
Fresh white
Black
Fresh white
Black
Fresh white
Fresh white
For usage of 3-, 4-way flow
For usage of 2-way flow
Without
T-duct joint
Chamber type
(Note 5, 6, 13)
With
T-duct joint
Direct installation type (Note 7)
(colorimetric method 65%)
(colorimetric method 90%)
(colorimetric method 65%)
(colorimetric method 90%)
Wireless type
Heat pump
Wired type (Note 14)
Wired type (Note 14)
(components: KDDP55C160-1, KDDP55C160-2)
(components: KDDP55C160-1, KDDP55C160K2)
BRC7M634F (fresh white) / BRC7M634K (black)
59
EDAR282024
Model
FCA100CVM2
FCA140CVM2
BYCQ125EEF
BYCQ125EEK
BYCQ125EAF
BYCQ125EAK
BYCQ125EAPF
BYCQ125EASF
KDBH551C160
KDBH552C160
KDB55J160F
KDDP55C160
KDDP55C160K
KDDP55X160A
KAF556D160
KAF557D160
KAF552D160
KAF553D160
KDDFP55C160
KAF5511D160
KAF5512D160
KAF555D160
KAF550D160
KDJP55C160
KDTP55K160A
BRC1E63
BRC2E61
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
BRP11B62
KRP4AA53
KRP1H98A
BRCS01A-5
C: 3D109328Q
Publicidad
