Setup Instructions; Site Preparation - Polygroup SUMMER WAVES Serie Manual Del Usuario

Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.
WARNING
- DO NOT overfill the pool and/or allow people to lay over or sit on pool wall - DOING SO CAN CAUSE PERMANENT INJURY!
Drain pool to the proper level after a heavy rain.
TIP:
It will be much easier to install your pool if you unfold it and let it lay in direct sunlight for about 2 hours prior to installation. This will help to ensure a
wrinkle-free fit because the pool material will be more pliable, allowing it to form into shape during installation.
WARNING
- VERY IMPORTANT! SITE MUST BE LEVEL, STABLE, COMPACTED SOIL.
• The pool must be assembled on a smooth and level site of firm soil that is free of stones, gravel, sticks, blacktop, or other oil-based compounds.
• Before setting up your pool, it is recommended that you clear the area of hardy grasses. Certain types of vigorous grasses such as St. Augustine and
Bermuda can grow through the liner. A ground cloth or tarp may be helpful in preventing this from occurring. Grass growing through the liner is not covered
under warranty.
• Do not install pool on a wooden deck or any type of wooden surface. You cannot use SAND and/or uncompacted soil to provide a level surface for this pool;
it will only wash out.
• FAILURE TO FOLLOW THE INSTRUCTIONS BELOW WILL CAUSE POOL TO COLLAPSE AND WILL VOID THE WARRANTY!

Site Preparation

1. Select a level area, and completely remove all debris, twigs, stones, etc. DO NOT select an area under overhead electrical lines, trees, or within 15 feet of a
house, building, etc.
2. The pool shall be located a minimum distance of 6ft (1.83m) from any electrical receptacle.
3. All 125 volt, 15 and 20 ampere receptacles located within 20ft (6.0m) of the pool shall be protected by a ground fault circuit interrupter (GFCI).
The 20ft (6m) distance is measured via the shortest straight line distance the supply cord would follow without piercing a floor, wall, ceiling, doorway, window, or
other permanent barrier.
4. Contact your local utilities, checking that no underground cables, telephone lines, gas lines, etc. run beneath the area you have selected.

Setup Instructions

1. Locate a level and flat area to set up the pool. Make sure the ground is free from sharp objects as they may puncture the pool.
2. LIFT the pool liner across the ground. DO NOT drag the liner from one location to another location.
3. It is recommended to let the pool sit out in direct sunlight for about 2 hours prior to installation. (see TIP above)
4. Locate the pool so that the pump opening is 10 to 21 feet away from the electrical outlet.
5. Carefully unfold the Quick Set pool liner 1 and inspect seams for manufacturing defects. With the inflatable ring on the top side, lay out the pool in the area
®
selected, making sure the pool bottom is both flat and oval-shaped. Position the intake / outlet fitting holes in pool wall so they
are 10 to 21 feet from the electrical outlet you plan to use for the pool pump. Pull out the four rectangular flaps (two on each side)
from the base of the liner, which will be used for the U-shaped Pipes.
6. Locate the four U-Shaped Pipes 5. Insert the eight Pipe Caps 4 onto the ends of the pipes, slightly rotate until the lock
buttons click in place (Fig. 1). Then place two pipes on each side of pool, near the rectangular flaps.
7. Take out all four Horizontal Beams 2. For each pair of beams, press down the lock buttons, insert the swaged beam into
the plain beam, and slightly rotate until the buttons click in place. Then tap to secure the four plastic Beam Plugs 3 onto
the ends of the two Horizontal Beam Assemblies. Now locate the sleeves stitched along the long sides of pool. Slide one
Horizontal Beam Assembly into each sleeve, holes on the beam and on the sleeve aligned as in Fig. 2.
3
Horizontal
Beam Assembly
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.
8
SETUP INSTRUCTIONS
2
Deflated Top Ring
Holes Facing Out
FIG. 2
Extended operating days and hours during peak season requirements.
2
Insert the Horizontal
Beam Assembly into the Sleeve
Sleeve
4
5
FIG. 1
3