Publicidad
PRECAUTIONS FOR USE
INSTALLATION
UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.
DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE AND BEFORE
ALL OTHER CONNECTIONS HAVE BEEN MADE.
DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS
AROUND THE UNIT FOR VENTILATION.
CONNECTION
1.
CONNECT THE POWER CORD TO AC OUTLET AND SWITCH ON THE MAIN POWER SWITCH AT THE
BACK OF UNIT.
2.
WHEN YOU FIRST PLUG THE UNIT INTO THE MAINS, THE UNIT WILL GO INTO STANDBY MODE.
3.
CONNECT THE SPEAKER WIRE TO THE SPEAKER TERMINAL LOCATED ON THE REAR SIDE OF THE
UNIT.
4.
TURN ON THE POWER AND SELECT " CD " FUNCTION. IF THE LCD DISPLAY IS ON WITH BACKLIGHTING,
IT'S MEAN THE POWER SUPPLY IS NORMAL. NOW YOUR SYSTEM IS READY TO PLAY THE MUSIC.
THE POWER CABLE/DISCONNECT DEVICE SHALL REMAIN EASY TO OPERATE/DISCONNECT.
LISTENING TO RADIO
OPERATION
1.
SET THE FUNCTION SELECTOR TO " RADIO" POSITION.
2.
SELECT THE DESIRED RADIO FREQUENCY BAND FROM BAND SELECTOR.
3.
TURN THE TUNING CONTROL TO SET THE DIAL POINTER AGAINST THE STATION FREQUENCY AS
DESIRED.
4.
ADJUST VOLUME CONTROLS FOR THE DESIRED VOLUME LEVEL.
FM & FM-STEREO RECEPTION
SET THE FM MODE SELECTOR AT " FM " POSITION. PROGRAMS ARE RECEIVED IN MONO MODE. IN
PARTICULAR WHEN STEREO SIGNALS ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN
MONO.
SET THE FM MODE SELECTOR AT " FM-ST " POSITION FOR RECEIVING STEREO PROGRAMS. THE
STEREO LED INDICATOR WILL LIGHT UP TO SHOW FM STEREO PROGRAM IS RECEIVING.
HINTS FOR BEST RECEPTION:-
- AM : THE RECEIVER HAS A BUILT-IN AM BAR ANTENNA. IF AM RECECPTION IS WEAK, SLIGHTLY ROTATE
OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
- FM : THE RECEIVER HAS A BUILD-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FRO BEST RECEPTION.
PHONO
NOTED:
-
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING, AND RE-SECURED AGAIN AFTERWARDS.
1.
PRESS THE " PHONO " FUNCTION SWITCH.
2.
SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE
RECORD TO BE PLAYED.
3.
PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).
4.
LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD SIDE.
THE PLATTER WILL BEING TO ROTATE.
5.
PLACE THE TONE ARM TO THE DESIRED POSITION OF THE RECORD.
6.
ADJUST THE VOLUME TO THE DESIRED LEVEL.
7.
AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. LIFT THE TONE ARM
FROM THE RECORD AND RETURN IT TO THE REST.
8.
TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
REMARK : AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST RACK FINISH. IN THIS CASE, SELECT THE AUTO-STOP SWITCH TO " OFF
" POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH TO " ON " POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION.
EN-2
Publicidad
