Publicidad
Enlaces rápidos
A
B
E
F
Fig. 1
Cross pin
Hanger
Set screw
ball
Downrod
Fig. 2
Hook-up
(5) wires
Safety
cable
Downrod
Security
Mounting
screws
coupler
Cotter
Downrod
pin
pin
Fan
body
Fig. 4
C
D
Outlet box
Hanger bracket
Flat washer
Spring Washer
Outlet Box Screw
Mounting
coupler
assembly
Screws
Fan
body
Fig. 3
Cross pin
Ground
wire
Hanger ball
Set screw
Canopy
Canopy
cover
Yoke
cover
Fan
body
Fig. 5
DOWNROD KIT INSTALLATION
A)
Mounting coupler assembly
B)
Hanger bracket
C)
Canopy
INSTALLING THE HANGER BRACKET
REMEMBER -Turn off the power !
Attach hanging bracket to outlet box using screws
provided with the outlet box. (Fig.1)
HANGING THE FAN
Step 1. Remove hanger ball from downrod by
loosening set screw in the side of the hanger ball.
Slide hanger ball down and remove cross pin; remove
hanger ball. (Fig. 2)
Step 2. Carefully support the fan motor assembly in
it's styrofoam packing so the top of the motor facing
upward
Step 3. Slip the wires from the fan motor through the
mounting coupler assembly, and than tighten
mounting coupler assembly to the fan body with four
mounting screws. (Fig. 3)
Step 4. Carefully feed the electrical lead wires and
safety cable from the fan through the downrod.
Thread downrod into coupler until holes align. Insert
downrod pin through holes in mounting coupler and
downrod; clip cotter pin through small hole in end of
downrod pin to hold downrod in place. (Fig. 4)
Step 5. Tighten security set screws against downrod
using a large flat blade screwdriver to ensure a tight fit
against downrod.
Step 6. Slip the wires from the fan motor through the
yoke cover and canopy cover and canopy onto the
downrod. Slide the hanger ball onto the downrod,
insert the cross pin through the downrod. Pull the
hanger ball up so the cross pin seats in the channel in
the hanger ball. Tighten the set screw. (Fig. 5)
FOR FACET FAN
Model: 99058FXX
PARTS
D)
Canopy cover
E)
Downrod Asm
F)
Yoke cover
Publicidad
Manuales relacionados para Hinkley 99058F Serie
Resumen de contenidos para Hinkley 99058F Serie
- Página 1 DOWNROD KIT INSTALLATION FOR FACET FAN Model: 99058FXX PARTS Mounting coupler assembly Canopy cover Hanger bracket Downrod Asm Canopy Yoke cover INSTALLING THE HANGER BRACKET REMEMBER -Turn off the power ! Outlet box Attach hanging bracket to outlet box using screws Hanger bracket provided with the outlet box.
- Página 2 Step 1. Attach the wood screw and the flat washer to the ceiling joist as shown (do not fully tighten). Slide the Wood ceiling joist cable clamp onto the safety cable from the fan. Loop the safety cable around the wood screw that was just attached to ceiling joist.
- Página 3 INSTALACIÓN DEL KIT DE BAJADA PARA FACET FAN Modelo: 99058FXX PARTES Conjunto del acoplador de Cubierta de dosel montaje Montaje de la Soporte de suspensión varilla Pabellón Cubierta de yugo INSTALACIÓN DEL SOPORTE DE SUSPENSIÓN RECUERDE - ¡Apague la energía! caja de salida Fije el soporte para colgar a la caja de salida con los tornillos provistos con la caja de salida.
- Página 4 Paso 1. Fije el tornillo para madera y la arandela plana a la viga del techo como se muestra (no apriete completamente). Viga de techo de madera Deslice la abrazadera del cable en el cable de seguridad del ventilador. Pase el cable de seguridad alrededor del tornillo para madera que acaba de colocar en la viga del techo.
- Página 5 INSTALLATION DU KIT DOWNROD POUR VENTILATEUR FACET Modèle:99058FXX PARTES A) Assemblage du coupleur de D) Couverture montage d'auvent B) Support de suspension E) Assemblage de la C) Pavillon tige F) Couverture de joug INSTALACIÓN DEL SOPORTE DE SUSPENSIÓN RECUERDE - ¡Apague la energía! boîte de sortie Fije el soporte para colgar a la caja de salida con los tornillos provistos con la caja de salida.
- Página 6 Étape 1. Fixez la vis à bois et la rondelle plate à la solive de plafond comme illustré (ne serrez pas complètement). Faites Solive de plafond en bois glisser le serre-câble sur le câble de sécurité du ventilateur. Enroulez le câble de sécurité autour de la vis à bois qui vient d'être fixée à...