GE AJCH08ACB Manual Del Propietario E Instalación página 5

www.GEAppliances.com
COOLMODE
Remote C ontrol
l. Px_ss COOL pad.
2. P*_ss LOW,IVIED or HIpads to set desired fire
speed.
3. Px_ss die INCREASEA/DECREASET padsto
set
the
desix_d temperature
60°F to 85°F in l °F increments.
Control Panel
l. Pxess d_e MODEpad until tile COOLindicator lig]lt is
lit and the LOW, MEDor Hlindicator light is lit fbr
dm (]esix_(] thn speed.
2. Px_ss the INCREASE&/DECREASET pads to set the
(]esix_(] temperature 60°F to 85°F in l °F increments.
A them/ostat is used to maintain tile room
temperature. Tile compressor will e}cle on and off
to keep tile room at tile set level of comtbrt. Set die
thermostat at a lo_r nm-nber and die indoor air will
become coolex; Set tile themlostat at a big]mr number
and tile indoor air will become _mnex;
NOTE:ff the air conditioner is off andis then turned on
while set to COOL, i t will take approximately3 minutes for
the compressor to start and cooling to begin.
CoolingDescriptions
ForNormal Cooling--Select the COOLmode and
HIGH or MEDtbn with a middle set temperature.
ForMaximumCooling--Select tile COOL mode
and HIGH tim with a lower set temperatm_.
ForQuieter& Nighttime
Cooling--Select
tile COOL mode
and LOWfbn wid_a middle set temperature.
NOTE: I f youswitch froma COOL setting to OFFerto
a fansetting wait atleast3 minutes beforeswitchingback
toa COOL s etting.
Fan Switch
Tile thn switch is located behind tile ti'ont grille on the
control box. Access through a hole in control box.
_A]mn set at
CYCLE (do_n)
tile thn e_cles on and off.
When set at
CONT (continuous, up)
tile tim runs all tile
time prodding a rnox_ balanced mmperatm_. The unit
is shipped in tile
CONTsetting.
FAN MODE
Use tile FAN mode to pro\ide _dr circulation and
filtering without cooling. Since tim only settings do not
provkle cooling, a tempenmlre setting will not be
displa}ed.
Remote Control
Px_ss FANpad. Press LOW,MED or HI pads to set
desix_d thn speed.
Control Panel
Px_ss die MODEpad until tile FANindicator light is lit
and tile LOW, MEOor HIindicator light is lit tbr the
desix_d tan speed.
Vent Control
T]_e vent control is located behind tile ti'ont grille on
tile right side of tile air (fischarge area. "_lmn set at
CLOSE, only tile air inside the room will be circulated
and conditioned. When set at OPEN,some inside air is
exhausted outside.
TO opell or
close
tile vent:
l. Remove tile ti'ont grille.
2. Remove tile vent card scx_.
3. Remove vent card, turn it over and replace it b}
locating rear hole in card over locating pin inside air
discharge and reattaching scre_ at fi'ont.
Theunit leavesthe factoryset at theCLOSE position.
._Locating i_oie
Screw hole "_.
OPEN position
(Meshendtowardback)
Screwha
CLOSE position
(Meshendtowardfront)
A# Direction
Horizont_fl lomers
on d_e fi'ont grille let
you control tile air
(lirection up and
doP_I/.
Remove the i]?ont
grille to a(!just the
vertical louvers
side-to_ide to
(fix_ct the air
left or fight.