Publicidad
Idiomas disponibles
Idiomas disponibles
EN
• You cannot charge your device wirelessly when using an ultra-thick (>
•
4 mm) protective phone case or a case with a pop socket.
T
• • This wireless charger only supports the protective cases that match
the magnetic structure of the iPhone.
• • Do not place any foreign objects between your device and the wireless
charger's surface, including metal pads on a car mount, magnetic
cards, door keys, coins, metal objects, or NFC cards, as they could
potentially demagnetize the wireless charger, affect the charging
speed, or cause overheating.
• • Wireless chargers make charging more convenient than wired
chargers, but confined by current wireless technology, their charging
speed is slower than that of wired chargers.
• • High temperatures will reduce charging speed and restrict power. It
is recommended that you charge your device in environments with
temperatures below 35°C / 95°F.
Important Safety Instructions
Please refer to the electrical and safety information on the bottom
before installing or operating the product.
• • Avoid dropping.
• • Do not disassemble.
• • Do not expose to liquids.
• • For the safest and fastest charge, use original or certified cables.
• • This product is suitable for moderate climates only.
• • The maximum ambient temperature during use of this product must not exceed
40°C.
• • Open flame sources, such as candles, must not be placed on this product.
• • Only use a dry cloth or brush to clean this product.
• • The socket-outlet shall be installed near the product and shall be easily
accessible.
• • Disconnection from line voltage should be made via the AC plug.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
01
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) Reorient or relocate
the receiving antenna. (2) Increase the separation between the equipment and
receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio
/ TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
Product Name: PowerWave Magnetic Pad Slim
Model: A2562
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1 800 988 7973
IC Statement
This device complies with RSS-216 of Industry Canada. Operation is subject to
the condition that this device does not cause harmful interference.
RSS-Gen Issue 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada's licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
02
Publicidad
