Publicidad
6
S
S
IGNITION SYSTEM
MART
WITCH
C
A
F
HEADLIGHTS
Headlights can be used without your passcode and with the
engine off.
WITH ENGINE OFF:
•
Press headlight button (E) once to turn headlights on for
one minute.
•
Press and hold headlight button (E) until headlights blink
twice to turn headlights on for five minutes.
NOTE!
If the engine is running and shuts off for any reason, the
headlights will also shut off.
BATTERY INDICATOR BUTTON (See Fig. 16)
The battery indicator button (F) is located on the SmartSwitch
Ignition module and is used to display the status of the battery.
The indicator will only work after the passcode has been entered
and is blinking green.
•
Press and hold battery indicator button (F) for three (3)
seconds.
•
The SmartSwitch Ignition Button (C) will light up and indicate
the battery status as follows:
RED
RED AND GREEN
GREEN
•
Press the battery indicator button (F) once to stop viewing
the battery status.
NOTE!
When the battery is too low and after the first unsuccessful start
attempt, the battery indicator button will blink for two (2) seconds
and then stay lit until battery is charged or until approximately
five (5) minutes since last attempted start.
E
Charge necessary
Charge recommended
Charge not necessary
RESETTING S
The SmartSwitch Ignition is preset at the factory with the default
code "321". To reset or change the passcode, the operator
does not have to be seated on the tractor.
F, E, and D are used as the numerical input buttons 1, 2, and
3 for entering the passcode.
B
1. Press the SmartSwitch Ignition (SSI) button (C) once (or
sit on the seat). Ensure the indicator is blinking blue.
2. Press and hold the (1) and (3) buttons (F and D) simulta-
neously for approximately three (3) seconds until the SSI
button changes to solid blue.
3. Using the numbered buttons, enter the desired passcode.
The passcode may be anywhere from one to five digits in
length.
4. After the desired passcode has been entered, press the
SSI button (C) once.
NOTE!
When the indicator flashes green, the passcode has been
D
accepted. If the indicator blinks red, the passcode has not been
accepted. Wait until the indicator returns to blinking blue and
repeat this procedure starting from step two (2).
S
S
MART
WITCH
The SmartSwitch System is equipped with courtesy lights that
are used to indicate system functions or faults.
FUNCTIONS
•
The SmartSwitch Ignition (SSI) Button (C) will blink blue
while waiting for the correct passcode to be entered. The
SSI button will blink green when tractor is ready to start and
remain solid green while running.
•
The park brake symbol (A) will be lit if the parking brake
has not been engaged during a start attempt.
•
The blade switch symbol (B) will blink if the attachment
clutch control is not in the "DISENGAGED" position during
a start attempt.
•
The Reverse Operation System (ROS) button (D) will be lit
when Reverse Operation System is in use.
•
The Headlight button (E) will remain lit while headlights are
in use.
•
During normal operation, the Battery Indicator button (F)
will not be lit.
FAULTS
•
The SSI Button (C) will blink red for two seconds if the wrong
passcode has been entered.
•
The Reverse Operation System (ROS) button (D) will blink
when there is a fault with the Reverse Operation System.
See "Reverse Operation System" in section 5 of this manual.
•
After the first unsuccessful start attempt, the battery indicator
button (F) will blink for two (2) seconds and then stay lit.
This indicates that the battery voltage is below normal
operating level. While engine is in operation, this light may
also indicate a charging system failure.
•
The headlight button (E) will blink when one or both of the
headlight bulbs fail.
•
All indicator lights will blink in the event the engine shuts
off for unknown reasons; for example, if the engine has run
out of fuel.
64
S
IGNITION SYSTEM PASSCODE
MART
WITCH
IGNITION SYSTEM LIGHTS
Publicidad
