Publicidad
Idiomas disponibles
Idiomas disponibles
•
In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and remove
the battery
AFTER USE
•
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
•
After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
BATTERIES
•
The battery supplied, if any, is partially charged (to
ensure full capacity of the battery, completely charge the
battery in the battery charger before using your power
tool for the first time)
•
Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
•
Do not use battery when damaged; it should be replaced
immediately
Do not disassemble the battery
•
•
Do not expose tool/battery to rain
•
Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
Charging battery
•
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
•
•
Battery level indicator 7
- press the battery level indicator button AB to show the
current battery level 7 a
! when the lowest level of the battery indicator
starts flashing after pressing button AB 7 b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button AB 7 c, the battery is not
within the allowable operating temperature range
•
Shadow line LED light 8
Your tool is equipped with an shadow line LED light
located under the upper guard.
This provides additional illumination on the saw blade
and the surface of the workpiece.
The LED light projects a shadow of the saw blade for
guiding tool along desired line of cut marked on the
workpiece
! always test out first on a piece of scrap material
The LED light will automatically turn on with a slight
squeeze of the trigger switch. It will turn off approximately
10 seconds after the trigger switch is released.
! the LED light will rapidly flash when the tool and/
or battery pack becomes overloaded or too hot
and the internal sensors will turn the tool off. Rest
the tool for a while or place the tool and battery
pack separately under air flow for cooling.
! the LED light will flash more slowly to indicate that
the battery pack charge level is low. Recharge the
battery pack.
The LED cleaning dial X built into the upper guard is
designed to clean the LED light. When the LED light gets
dim because of the sawdust accumulated on it, turn the
dial LED cleaning dial X in any direction to remove the
sawdust and make the LED light bright again
•
Battery protection
The tool is suddenly being switched off or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing button AB 7 c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level 7 b is shown by the battery level indicator
when pressing button AB; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
•
Mounting saw blade AA 2
! remove battery from tool
- take hex key A from storage B
- push spindle-lock button C and hold it while you
remove bolt D by turning hex key A CLOCKWISE (= in
same direction as arrow printed on saw blade)
! push spindle-lock button C only when tool is at a
complete standstill
- release spindle-lock button C
- remove flange E
! make sure that clamping surfaces H of flanges are
perfectly clean and face the blade
- open lower guard F with lever G and hold it while you
mount saw blade with saw teeth and arrow printed on
saw blade pointing in same direction as arrow on lower
guard
- release lower guard F
- mount flange E
- push spindle-lock button C and hold it while you tighten
bolt D with hex key A 1/8 turn past finger tight (ensures
slippage of saw blade when it encounters excessive
resistance thus reducing motor overload and saw
kickback)
- release spindle-lock button C
•
Adjusting cutting depth (0-57 mm) 9
- loosen knob K
- raise/lower foot plate J until desired cutting depth is set
on scale using cutting depth indicator L
- tighten knob K
- for an optimal quality cut, the saw blade should not
extend more than one teeth below the workpiece
•
Adjusting cutting angle (0-45°) q
- loosen knob M
- tilt tool until desired cutting angle is set on scale using
cutting angle indicator N
- tighten knob M
13
Publicidad
