Allen + Roth WSWS-CS1C Manual Del Usuario página 9

ASSEMBLY INSTRUCTIONS
Pole Installation
25. Insert 22 mm metal poles (X) into 25 mm metal
poles (Y). Using closed pole holders (ZZ) as a guide,
mark screw hole locations with a pencil. Drill 3/8 in.
diameter pilot holes at least 2-1/2 in. deep
locations, then insert drywall anchors (not included) into
the holes. Attach closed pole holders (ZZ) with
M4 x 38 mm screws (KK). Insert 25 mm metal poles (Y)
into closed pole holders (ZZ), securing with
M4 x 15 mm self-tapping screws (AB).
Note: Drywall anchors are not required if installing into a
stud.
Hardware Used
KK M4 x 38 mm Screw
ZZ Closed Pole Holder
AB
M4 x 15 mm Self-tapping Screw
26. Attach open pole holders (YY) to hutch panel
left (A) and hutch panel right (B), securing with M4
x 14 mm wood screws (MM). Insert 22 mm metal
poles (X) into open pole holders (YY), securing with
M4 x 15 mm self-tapping screws (AB).
Hardware Used
MM
M4 x 14 mm Wood Screw
YY
Open Pole Holder
AB M4 x 15 mm Self-tapping Screw
Adjustable Shelf Installation
27. Insert shelf pins (OO) where desired in cabinet, then
rest adjustable shelf (G) on top.
Note: Ensure the shelf pins (OO) are level.
Hardware Used
OO Shelf pin
25
X
at marked
KK
ZZ
x 9
x 3
x 3
26
YY
AB
x 9
x 3
YY
MM
x 3
27
G
x 4
Lowes.com/allenandroth
16
CARE AND MAINTENANCE
• Periodically check to make certain all components are properly positioned, free from damage and
firmly connected.
Y
• Use a soft, clean cloth that will not scratch the surface when dusting.
• Never use water to clean the furniture as it may cause damage to the finish.
• Wipe clean using a damp cloth and a mild cleaner. Wipe dry with a clean cloth.
• In the event that the furniture is stained or otherwise damaged during use, it is recommended you
call a professional to repair the furniture.
• Keep furniture away from direct sunlight as it may damage the finish.
• It is best to keep the furniture in a climate-controlled environment. Extreme temperature and
AB
humidity changes can cause fading, warping, shrinking and splitting of wood.
• Touch-up pen (XX) has been provided (except in Item #339204 & #2416433) to repair any small
nicks or scratches that may occur during assembly or shipping.
• If Item #339204 & #2416433 is damaged and touch-up is required please apply a quality wood
polish to the damaged surface. Polish not included with this item.
Drywall Anchor
TROUBLESHOOTING
PROBLEM
One end of long
shelf (V) is
Long shelf (V) can
not be installed
inside the closet.
The shelf is tilting.
Drawer slide
runner can not
slide into slide
tracks.
Drawer slides do
not go smoothly.
Drawer gaps are
OO
not even.
POSSIBLE CAUSE
The closet space is larger than
floating. 8 ft.
The closet space is smaller
than 8 ft.
The wall brackets and shelf
brackets are not installed at
the same level.
Slide runners reversed.
The slide runners do not align
with the slide tracks properly.
Slide runners are not level with
each other.
17
CORRECTIVE ACTION
1. Buy corresponding shelf bracket and
wall bracket (sold separately).
2. Replace long shelf (V) with a longer
shelf of a similar finish and style.
1.Shorten one side of the long shelf (V). Hire
an insured remodeler for installation.
2. Replace long shelf (V) with a shorter shelf
of a similar finish and style.
Use a quality level to ensure the brackets
are leveled with each other.
Reinstall the slide runner and ensure the
opening of slide runner is pointing backward.
Take out and repeat drawer installation.
Use the pilot holes on the tower as a guide
to level the slide runners.
Lowes.com/allenandroth