Testing And Adjustment; Testing - Garland GF24 Serie Instrucciones De Instalación Y Operación

INSTALLATION Continued
TO INLET OF SALAMANDER/
CHEESEMELTER MANIFOLD
FOR LEFT-MOUNTED SALAMANDER/CHEESEMELTER
SUBSTITUTE COMPONENTS SHOWN FOR ITEM 17 CIRCLED IN ADJACENT VIEW
TO INTER-CONNECT TUBING ( ITEM 18 - 4531608)
ATTACH SUPPORT CLAMP (ITEM 10 - 2640800)
TO SUPPORT BRACKET (ITEM 9 - 4531602)
17
WITH (2) #10-24 SELF-TAPPING SCREWS (ITEM 1
F32 - NOT SHOWN) PROVIDED
10
6 9
MARK HOLE LOCATIONS AND MOUNT
SUPPORT BRACKET (ITEM 9 - 4531602 ) TO RANGE
BACK WITH (2) #10-16 TEKS SELF-DRILL/TAP
SCREWS (ITEM 14 - F67 - NOT SHOWN) PROVIDED.
18 4531608
17 3013000
16 G01474-9
15 G01738-11
14 F67
13 G01738-14
12 G01738-16
11 3012800
10 2640800
9 4531602
8 4530189
7 076029-171
6 G01474-5
5 G01738-5
4 076029-204
3 2127503/2127500 4.5"wc 3/4"NPT REG. NATURAL GAS/10"wc 3/4"NPT REG. PROPANE GAS - PROVIDED WITH SALAMANDER/CHEESEMELTER
NAT: 4522421/4525049
2 4.5" wc 1" NPT/ 1" ISO 7-1 REG. NATURAL GAS OR 10"wc 1"NPT/1" ISO 7-1 REG. PROPANE GAS - PROVIDED WITH RANGE
PRO: 4522422/4525050
1 F32
ITEM NO. PART NUMBER

TESTING AND ADJUSTMENT

Testing

All fi ttings and pipe connections must be tested for
leaks. Use approved gas leak detectors, soap solution or
equivalent, checking over and around all the fi ttings and
pipe connections. DO NOT USE A FLAME! Accessibility to
all gas lines and fi ttings require that valve panel(s) lower
front panel(s), and/or oven rack(s) be removed. It may be
necessary to remove, or at least raise and securely prop
griddle(s), hot top(s), and/or top grate(s). All parts removed,
(including fasteners), should be stored safely for re-
installation.
1. Be sure that all valves and thermostats are in the "OFF"
position.
Part # 4525587 Rev 4 (29 April 14)
16
13
12
TO OUTLET OF SALAMANDER/
CHEESEMELTER REGULATOR
ATTACH SUPPORT CLAMP (ITEM 10 - 2640800)
TO SUPPORT BRACKET (ITEM 9 - 4531602)
WITH (2) #10-24 SELF-TAPPING SCREWS (ITEM 1
F32 - NOT SHOWN) PROVIDED
MARK HOLE LOCATIONS AND MOUNT
SUPPORT BRACKET (ITEM 9 - 4531602) TO
BACK WITH (2) #10-16 TEKS SELF-DRILL/TAP
SCREWS (ITEM 14 - F67 - NOT SHOWN) PROVIDED.
3/4" X 51" X 33" TUBING
3/4" CC X 3/4" NPT STRAIGHT FITTING
3/4" NPT X 1/2" NPT 90 DEG. REDUCING ELBOW
3/4" NPT X 3.5" PIPE NIPPLE
SCREW - #10-16 X 1/2" HEX WASHER HEAD TEKS SELF-DRILL/TAP (NOT SHOWN)
3/4" NPT X 2.000 PIPE NIPPLE
3/4" NPT X 22.750 PIPE NIPPLE
1" NPT X1" NPT X 3/4" NPT REDUCING TEE
PIPE SUPPORT BRACKET CLAMP
PIPE SUPPORT BRACKET 48/60
1" NPT PIPE UNION
1" NPT 90 DEGREE ELBOW(SUPPLIED WITH RANGE)
90 DEGREE ELBOW 3/4" NPT
3/4" NPT X 6.5" PIPE NIPPLE
1" NPT X 2" PIPE NIPPLE (ONE SUPPLIED WITH RANGE)
SCREW - #10-24 X 1/2" PAN HD SELF-TAP TYPE F (NOT SHOWN)
DESCRIPTION
NOTE: CUT TUBING (ITEM 18 - 4531608) TO SIZE AS REQUIRED
TO SUIT SALAMANDER/CHEESEMELTER TOP OR REAR
MANIFOLD INLET CONNECTION
17
18
6
5
15
6
10
9
2. Turn on the main gas supply valve. Light all top section
pilots.
3. Leak test all valves and fi ttings as described at the
beginning of this section. Correct any leaks as required
and recheck.
4. Light the oven pilot.
5. Set the oven thermostat to maximum. Leak test all valves
and fi ttings as described at the beginning of this section.
Correct any leaks as required and recheck.
6. Shut off all valves and set thermostat dials to "OFF" or
lowest position. All units are tested and adjusted at the
factory, however, burners and pilots should be checked
upon installation and adjusted if necessary.
17
REGULATOR - 6.0"w.c.
3
NATURAL GAS OR 10.0"w.c.
PROPANE GAS (SUPPLIED
WITH SALAMANDER/CHEESEMELTER)
SUPPLIED WITH
7
RANGE
SUPPLIED WITH
4
RANGE
2
REGULATOR - 4.5"w.c.
NATURAL GAS OR 10.0"w.c.
PROPANE GAS (SUPPLIED
WITH RANGE)
4
8
4
11
1
2
1
1
4
1
1
1
2
Optional Interconnect Gas Kit
2
1
48in (1200mm) & 60in (1500mm) G/U/X
1
3
Part # 4531606
1
3
1
1
4
QTY
TO INLET OF RANGE
MANIFOLD
1" NPT GAS SUPPLY
CONNECTION
Page 13