English; Parts And Service; Name Plate - Nilfisk-Advance SH 460 Instrucciones De Uso

ENGLISH

INTRODUCTION
This manual will help you get the most from your Nilfisk SH 460. Read it
thoroughly before operating the machine.
Note: Bold numbers in parentheses indicate an item illustrated on page
2 (Figure A).
This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by Nilfisk service personnel
using Nilfisk original replacement parts and accessories.
Call Nilfisk for repair parts or service. Please specify the Model and Serial
Number when discussing your machine.

NAME PLATE

The Model and Serial Number of your machine are shown on the Nameplate
on the machine. This information is needed when ordering repair parts for the
machine. Use the space below to note the Model and Serial Number of your
machine for future reference.
MODEL
SERIAL NUMBER
UNCRATING
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that
it can be inspected by the carrier that delivered it. Contact the carrier
immediately to file a freight damage claim.
B - FILL THE SOLUTION TANK
1 Pre-mix the carpet shampoo with water in a separate, clean container.
Follow the instructions on the shampoo package carefully. For best
results, use Arid Foam™ cleaner, which is specially formulated to
work with the SH 460.
2 Use the funnel supplied with the machine to fill the solution tank. The
funnel allows excess foam to escape; place a bucket nearby to catch
the excess foam. First put in the pre-mixed shampoo, then continue
filling with water.
3 Do not fill above the 15.9 liters (3-1/2 gallon) line marked on the back
of the machine. Over-filling will result in inadequate foaming and an
over-wet carpet.
4 Close the cap tightly on the tank.
WARNING!
Loosen the Solution Drain (10) and Solution Fill (14) slowly
when draining or re-filling the Solution Tank (6). The Solution
Tank can become pressurized during use!!
24 - FORM NO. 041384 / SH 460
ADJUST THE BRUSH
1 Plug the machine in to a properly grounded outlet. Step down on the
Handle Release Pedal (11) and move the Control Handle (1) to a
comfortable operating position.
2 Starting with the brush up off the carpet, turn the Twist Grips (2) to start
the brush motor. Turn the Brush Adjustment Knob (9) to lower the
brush onto the carpet. Keep turning the knob until the machine just
begins to pull away. When correctly adjusted, the brush will help propel
the machine when the Twist Grips are turned.
A - KNOW YOUR MACHINE
1 Control Handle
2 Twist Grip
3 Foam Generation Lever
4 Attachment Port
5 Foam Control Valve
6 Solution Tank
7 Brush Housing
8 Foam Distribution Manifold
9 Brush Adjustment Knob
10 Solution Drain
11 Handle Release Pedal
12 Cord Hook
13 Power Cord
14 Solution Fill
15 Accessory Receptacle
USING THE SH 460
1 Vacuum surface debris from the area to be cleaned. Pre-spray soiled
spots.
2 Plug the Power Cord (13) into a properly grounded outlet.
3 Step on the Handle Release Pedal (11) and lower the handle to a
comfortable operating position.
4 With the Foam Control Valve (5) in the "Brush" position, push the Foam
Generation Lever (3) down. In the down position, the machine will
generate foam continuously until the lever is shut OFF (back to the
middle position). The lever may also be held up in the Temporarily ON
position, where it will automatically revert to the OFF position when
released.
5 When foam begins to appear at the front of the machine, turn the Twist
Grips (2) to start the brush motor. When correctly adjusted, the brush
will help propel the machine (see Adjust the Brush). Twist the Grips
forward to propel the machine forward, twist them back to propel the
machine backward.
6 Start at the right side of the room. Working from right to left will prevent
leaving a wheel track on the carpet. Make a forward pass with the foam
ON. Turn the foam OFF 2-3 feet before the end of the pass.
7 Go over the same path in reverse with the foam OFF.
8 Move to the left and repeat steps 6 and 7. Overlap passes at least 5
cm (2 inches) to prevent streaking. In extremely soiled areas, it may
be necessary to move the machine back and forth over the spot several
times.
CAUTION!
Always clean the brush when going from one color carpet to
another to prevent color transfer!