Nilfisk-Advance SH 460 Instrucciones De Uso página 25

USING THE SH 120 T POWER BRUSH ATTACHMENT
CAUTION!
Before using the SH 120 T, test upholstery for color-fastness.
Put some shampoo on a clean, white cloth and work it into the
upholstery fabric in an inconspicuous place. Do not use if color
bleeds onto the white cloth!
WARNING!
Loosen the Attachment Port (4) slowly. The Solution Tank can
become pressurized during use!!
1 Remove the cap from the Attachment Port (4) on the SH 460. Connect
the hose from the SH 120 T to the Attachment Port.
2 Move the Foam Control Valve (5) to the "Attachment" position.
3 Plug the electrical cord from the SH 120 T into the Receptacle (15) on
the SH 460.
4 Move the Foam Generation Lever (3) DOWN on the SH 460 for
continuous foam generation.
5 Turn the foam flow ON at the Power Brush. When foam appears, turn
the Power Brush ON. Run the brush continuously and apply foam as
needed. Keep the brush in constant motion over the material being
cleaned. Overlap passes to assure complete coverage and prevent
streaking.
CAUTION!
Do not bear down on fabrics with the Power Brush. Bearing
down may damage fabrics.
AFTER USING THE SH 460
1 Turn the Foam Generation Lever (3) OFF.
2 Move the handle to the upright position to lift the brush off the floor.
Always move the handle to the upright position when the machine is
not in use to prevent the brush bristles from being bent over and taking
a "set".
3 Unplug the Power Cord (13) and wrap it around the Cord Hook(12)
and the Handle (1) for storage.
TECHNICAL SPECIFICATIONS (as installed and tested on the unit)
Model
Model Number
Voltage/frequency
Rated Power
Protection Class (electrical)
Protection grade (mec, moist, dust)
Sound Pressure Level (at 1.5m)
Vibrations at the Hand Controls
4 Drain unused solution from the tank into a separate container for future
use. The Drain (10) is located at the bottom rear of the solution tank.
Flush the Solution Tank (6) with warm, clean water.
5 Rinse the underside of the Brush Housing (7).
6 Wipe the machine with a clean, damp cloth. Store the machine indoors
in a clean, dry place.
NOTE: If the supply cord is damaged, it must be replaced by the manufac-
turer or its service agent or a similarly qualified person in order to
avoid a hazard.
AFTER USING THE SH 120 T
1 Turn the Foam Generation Lever (3) OFF at the SH 460.
2 Unplug the Power Cord (13) and wrap it around the Cord Hook(12) and
the Handle (1) for storage.
3 Disconnect the Power Brush from the SH 460.
4 Carefully rinse the SH 120 T hose and brush with clean water, DO NOT
allow water to reach the electric motor!
5 Wipe the Power Brush with a clean, damp cloth. Store indoors in a
clean, dry place.
WARNING!
Always unplug the power cord before attempting any machine
maintenance.
CLEAN THE BRUSH
Always clean the brush when going from one color carpet to another to
prevent color transfer!
Unplug the machine and tip it back. Rinse the underside of the brush housing
with water until the water runs clear. Clean the brush of any lint or carpet fiber,
string or hair.
FOAM DISTRIBUTION MANIFOLD
Once a month, or whenever an uneven foam pattern appears, clean out the
Foam Distribution Manifold. Remove the plug (8) and run the bottle brush
(included with the machine) through the manifold several times.
SOLUTION TANK
Flush the Solution Tank (6) with warm, clean water. Inspect the Solution Drain
(10), Solution Fill (14) and Attachment Port (4) caps to make sure they fit
securely and are not damaged.
V/Hz
W
dB(A)/20µPa
2
m/s
SH 460
66245350
220-240/50
750
IP34
<67.5
2
<2.5m/s
FORM NO. 041384 / SH 460 - 25