Publicidad
Idiomas disponibles
Idiomas disponibles
en
Safety instructions
R
Please read and pay particular attention to the safety information in the instruction manual.
W Danger of electric shock!
Connect and operate the appliance only according to the type plate specifications. To avoid p otential
hazards, repairs must only be carried out by our customer service personnel.
If the power cord of this appliance is damaged, it must be replaced with a special connection cord,
which is available from our after-sales service. Should a fault occur, pull the plug or disconnect from
the mains immediately.
Only an appliance which has been correctly installed according to these installation instructions can
be used safely. Attach loose furniture to the wall with a conventional bracket.
The appliance contains permanent magnets that may influence electronic implants such as
pacemakers or insulin pumps. Persons wearing electronic implants must maintain a minimum
distance of 10 cm from the front of the appliance and from the following parts upon removal: milk
container, milk system, water tank and brewing unit.
Included in delivery (for installation)
a Fully automatic coffee machine
b Installation instructions
c Connecting cable
d Assembly bracket
e Spacer
Installing the appliance
Make sure there is adequate aeration. To do this, remove the
rear panel or cut out an opening of 500 x 400 mm. There must
be a gap of at least 35 mm between the wall and base of the
unit or the rear panel of the unit situated above. The ventilation
slots and intake openings must not be covered. Also follow the
installation instructions for the appliance situated above or below.
If installing the appliance above a warming drawer, the height of
the recess must be 590 mm. If the appliance is installed directly
under a décor panel, ensure that there is a ventilation slot of at
least 200 cm². The ideal installation height for the fully automatic
coffee machine, measured from the floor to the lower edge of the
appliance, is 950 mm.
1 Unpack all the parts and check for any damage in transit.
Do not operate a damaged appliance.
2 Take note of the installation dimensions of the particular
model.
Important: 3 opening angles can be selected for the door.
Depending on the opening angle required, the mounting distance
to the wall should be observed before installation if it is on the left
side.
■ O pening angle approx. 110° (as delivered)
= mounting distance to the wall at least 350 mm on the left.
■ O pening angle approx. 155°
= mounting distance to the wall at least 650 mm on the left.
For this purpose, remove the two limits on the upper and lower
hinges.
■ Opening angle approx. 92° (requires special accessory)
= mounting distance to the wall at least 100 mm on the left.
For this purpose, replace the two limits on the upper and lower
hinges with special accessory no. 10020041.
3 Remove the installation template on the back of the installation
instructions. Place the installation template at the front edge
of the unit and screw on the assembly bracket d as shown
with two fastening screws f. The assembly bracket must be
positioned at the base of the unit and the wall such that no
gap is present.
4 Set the mains switch U to h. Plug the connecting cable c
into the socket first and then into the appliance (clicks into
place). It must not be trapped or kinked. Put the appliance to
be plugged in just on to the edge of the unit.
Important: The distance between the appliance and the back wall
must be at least 35 mm.
2
f 5 fastening screws (silver)
g 2 fastening screws (long/black)
h 2 fastening screws (short/black)
i 1 sleeve (black)
j 2 sleeves (white)
5 Push the appliance into the unit until it clicks into place. Check
that the appliance is in the middle. If necessary, align the
appliance. To do so, pull the appliance out a little, remove the
appropriate spacers e and attach to the left side (top and
bottom). Push the appliance into the unit until it clicks into
place.
6 Take hold of the appliance door on the right next to the outlet
and open. Remove the drip tray Y. Pull the cover X on the
bottom left-hand side forwards and remove. Pull out the
accessories drawer Z and put to one side.
7 First, screw on the appliance as shown using 2 of each of
the fastening screws f and g as well as 2 sleeves j. Then
screw tight at the top right of the unit using 1 fastening screw
f and sleeve i.
8 Only for the expert
In very few cases, the door of the fitted fully automatic
machine can jam due to a warpage in the built-in units. The
door can be adjusted. To do this adjust the hinges at the top
and the bottom.
I. Adjust the depth of the door by turning the screws V.
II. Turn the screws W to adjust the inclination and the
horizontal position of the doors.
9 Insert the cover X and fix with the two black fastening
screws h.
10 Replace the drip tray Y and accessories drawer Z and close
the appliance door.
Publicidad
