Publicidad
Idiomas disponibles
Idiomas disponibles
Safety, performance, and dependability have been given
top priority in the design of your brushcutter attachment.
INTENDED USE
This brushcutter attachment is approved for use with all
Ryobi / Homelite petrol-driven power head of 30CC or less,
and electric-driven power head RPH1200, RLT1238I, and
RBC1226I.
It is intended to be used only by adults who have read and
understood the instructions and warnings in this manual
and relevant powerhead manual and can be considered
responsible for their actions. This product is only intended
for use outdoors in a well ventilated area. For safety
reasons, the product must be adequately controlled by
using two-handed operation.
The product is intended for cutting long grass, weed, small
trees, brush, and similar vegetation at or about ground
level. The cutting plane should be approximately parallel
to the ground surface. The product should not be used to
cut or trim hedges, bushes, or other vegetation where the
cutting plane in not parallel to the ground surface.
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later use.
GENERAL SAFETY WARNINGS
FOR ASSEMBLING WITH PETROL-DRIVEN POWER
HEAD
■
For safe operation, read and understand all instructions
before using the product. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
■
Never start or run the engine in a closed or poorly
ventilated area; breathing exhaust fumes can kill.
■
Do not touch area around the silencer or cylinder of the
product, these parts get hot from operation.
■
Always stop the engine and allow it to cool before
making any adjustments.
■
Do not smoke when mixing fuel or filling fuel tank.
■
Mix and store fuel in a container approved for fuel.
■
Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
■
Stop the engine and allow to cool before refueling or
storing the unit.
■
Allow the engine to cool; empty the fuel tank and oil
tank (if applicable), and secure the unit from moving
before transporting in a vehicle.
WARNING
When the throttle trigger is released and the engine
is running at idle speed, the blade must not move. If it
does continue to move, there is risk of severe injury to
the operator. Do not use the machine. Return it to an
authorized service centre for professional adjustment.
FOR ASSEMBLING WITH ELECTRIC-DRIVEN POWER
HEAD
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool'' in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
WORK AREA SAFETY
■
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
■
Do
not
operate
power
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
■
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
■
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
■
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
■
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
■
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
■
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
■
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
tools
in
explosive
BG
UK
English |
1
Publicidad
