Publicidad
Idiomas disponibles
Idiomas disponibles
• If tool is not to be used for a period of time,
lubricate it, disconnect it from the air supply line
and store it in a dry place with moderate
temperature.
• Store tools when not being used in a high, dry
and locked area that can not be accessed by
children.
• Be aware of slippery surfaces.
• Wear gloves to protect from cuts and abrasions,
and heat.
• Release the start-stop device in the case of
interruption of energy supply.
• For overhead work, wear a safety helmet.
• Call for minimum gripping length of 10 mm
• Assess the risk of others.
Work area hazards can cause injury.
Risk of whipping compressed air hoses.
• Air under pressure can cause severe injury
• Always shut off air supply, drain air hose, and
disconnect tool when not in use and before
changing accessories or making repairs.
• Never direct exhaust or air at yourself or
anyone else.
• Whenever universal twist couplings are used
always use lock pins and whipcheck safety
cables to safeguard against hose-to-tool
connection failure.
• Attach air lines securely.
• Do not carry tool by hose.
• Check the air hose and fittings regularly for wear.
• Do not connect quick-connect couplings directly
to the tool.
• Use a whip air hose no longer than 60" (150 cm).
Whipping compressed air hose can cause injury.
Untrained users can create hazards.
• Secure work with a clamp or a vise whenever
possible.
• Overhang of the mounted point will decrease the
permitted speed.
• Use the right tool. Do not use a tool that is too
light or too heavy for the work.
• Do not force tool.
• Operate air tools at 90 psig (6.2 bar, 620 kPa)
maximum air pressure.
• It is expected that users adopt safe working
practices and observe all local, regional or
country legal requirements when installing,
using or maintaining this tool.
Improper use can cause injury.
Improper parts, maintenance, repairs, and/or lack of
maintenance can create hazards. These hazards can
cause injury.
• Replace the consumable/inserted tool to prevent
an increase in noise and vibration levels.
• Do not modify or make temporary repairs. Use
only genuine
Snap-on
maintenance and repair. Servicing and repairs
should be performed only by trained personnel.
Use only lubricants that are recommended by
Snap-on
Tools Company.
• Do not use the tool if it vibrates too much, makes
unusual noises, has loose parts, or shows any
other sign of damage.
ZPT1800ACE Rev D
replacement parts for
EN
EN
• If tool malfunctions, discontinue use and
immediately arrange for service and repair. If it
is not practical to remove the tool from service,
shut off the tool air supply, write a warning tag
and attach the tag to the tool.
• Do not remove any manufacturer fitted safety
devices (e.g., wheel guards, safety trigger,
speed governors).
• If this tool becomes damaged beyond repair,
disassemble and degrease the tool. Then
separate all parts by material type and recycle.
Check speed of the tool without inserted bit regularly;
also check speed and do a simple check for vibration
after every servicing.
Impact Wrench Safety Messages
Using damaged and incorrect sockets or accessories
can cause flying particles.
• Do not use chipped, cracked or damaged sockets
or accessories.
• Use only impact sockets and accessories.
• Periodically check the force to pull-off a socket
from the square. Inadequate pull-off force may
allow the socket to come off when rotating.
• Use only ball-joint flexible sockets. Do not use
square block type flex sockets.
Flying particles can cause injury.
Risk of personal injury.
• An impact wrench is not a torque control device.
• Do not use an impact wrench for torque control.
• Use a torque wrench for torque control.
Improperly torqued fasteners can cause equipment
damage that may result in personal injury.
SAVE THESE INSTRUCTIONS
Specifications
Specifications at 90 psig (6.2 bar, 620 kPa)
Square Drive Size ............................................... 1"
Max Torque.......................1800 lbs. ft. (2439 N•m)
Recommended Air Pressure ..... 90 psig (620 kPa)
Air Consumption, Free Speed....8.6 cfm (67.5 SCFM)
Air Consumption, Working .......6.3 cfm (53.5 SCFM)
RPM, Free Speed CW (CCW) ........................6500
Blows per Minute .............................................825
Air Inlet Thread Size ...........................1/2"–14 NPT
Air Supply Hose Size .......... 1/2" (12.7 mm) ID min
Dimensions:
Height................................................6.38" (162mm)
Width...................................................3.78" (96mm)
Length (PT1800A)...............................14.76" (375mm)
Length (PT1800AL)..............................19.16" (486mm)
Weight ...............................................15.5 lbs (7 kg)
Noise* (Tested in accordance with ISO
Standard 15744)
*Sound Pressure Level............................ 102.7 dBA
*Sound Power Level ................................ 108.1 dBA
Vibration** (Tested in accordance with ISO
Standard 28927-12)
4
(3/19)
Publicidad
