Bosch UniversalHeat 600 Manual Original página 11

Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Storage surface
(2) On/off switch and power settings
(3) Nozzle
(4) Heat shield, removable (UniversalHeat 600)
a)
(5) Surface nozzle
Technical Data
Hot air gun
Article number
Rated power input
Airflow
Temperature at the nozzle outlet
Temperature measurement accuracy
Weight according to EPTA-Procedure 01:2014
Protection class
A) The amount of air increases when the temperature rises from 50 °C to 300 °C/600 °C. The speed of the fan is identical at all power settings.
B) At an ambient temperature of approx. 20 °C
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise/vibration information
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A).
Total vibration values a (triax vector sum) and uncertainty
h
2 2
K: a ≤2.5 m/s , K=1.5 m/s .
h
Operation
Starting Operation
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool.
Creation of Smoke During Initial Use
A coating protects the metal surfaces from corrosion ex-
works. This protective layer evaporates during initial use.
Switching On
Slide the on/off switch (2) upwards.
Switching Off
Slide the on/off switch (2) downwards into the 0 position.
UniversalHeat 600: After working at high temperat-
u
ures for a prolonged period, let the power tool cool
down by briefly running it at the 50 °C power setting
before switching it off.
Selecting a power setting
You can choose between different power settings using the
on/off switch (2):
Bosch Power Tools
l/min
B)
kg
a)
(6) Glass protection nozzle
a)
(7) Angle nozzle
a)
(8) Reflector nozzle
a)
(9) Reducing nozzle
a)
(10) Heat shrink plastic tube
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
EasyHeat 500
3 603 BA6 0..
W 1600
240/450
°C 300/500
±10 %
0.47
/Ⅱ
EasyHeat 500
Setting °C l/min Setting
– –
300 240
500 450
UniversalHeat 600:
When changing from 50 °C to 300 °C/600 °C, the
u
speed and therefore the operating sound of the gun
do not change.
The 50 °C power setting is suitable for cooling down a
heated workpiece or for drying paint. It is also suitable for
cooling down the power tool before putting it down or chan-
ging the attachment nozzles.
Practical advice
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: Do not position the nozzle (3) too close to the work-
piece that you are using the power tool on. The resulting
build-up of air can cause the power tool to overheat.
Removing the heat shield (UniversalHeat 600)
When working in particularly tight spaces, you can remove
the heat shield (4) by turning it.
Caution: Nozzle is hot! Working without the heat shield
u
increases the risk of burns.
Always switch the power tool off and allow it to cool before
removing or attaching the heat shield (4).
English | 11
UniversalHeat 600
3 603 BA6 1..
1800
A) A) A)
200 /350 /500
A) A) A)
50 /300 /600
±10 %
0.53
/Ⅱ
UniversalHeat 600
°C l/min
50 200
300 350
600 500
1 609 92A 66S | (09.12.2020)