Publicidad
Idiomas disponibles
Idiomas disponibles
hazardous situation.
□ Keep handles and grasping surfaces dry, clean and free from
oil and grease. Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in unexpected
situations.
Battery tool use and care
□ Recharge only with the charger specifi ed by the manufacturer.
A charger that is suitable for one type of battery pack may create
a risk of fi re when used with another battery pack.
□ Use power tools only with specifi cally designated battery
packs. Use of any other battery packs may create a risk of injury
and fi re.
□ When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws or
other small metal objects, that can make a connection from
one terminal to another. Shorting the battery terminals together
may cause burns or a fi re.
□ Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, fl ush
with water. If liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause irritation or burns.
□ Do not use a battery pack or tool that is damaged or modifi ed.
Damaged or modifi ed batteries may exhibit unpredictable
behaviour resulting in fi re, explosion or risk of injury.
□ Do not expose a battery pack or tool to fi re or excessive
temperature. Exposure to fi re or temperature above 130°C may
cause explosion.
□ Follow all charging instructions and do not charge the battery
pack or tool outside the temperature range specifi ed in the
instructions. Charging improperly or at temperatures outside the
specifi ed range may damage the battery and increase the risk
of fi re.
Service
□ Have your power tool serviced by a qualifi ed repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
□ Never service damaged battery packs. Service of battery packs
should only be performed by the manufacturer or authorized
service providers.
Drill Safety Warnings
Safety Instructions for All Operations
□ Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory or
fasteners may contact hidden wiring. Cutting accessory or
fasteners contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an electric
shock.
□ Safety instructions when using long drill bits
● Never operate at higher speed than the maximum speed
rating of the drill bit. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the
workpiece, resulting in personal injury.
● Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting the
workpiece, resulting in personal injury.
● Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing breakage
or loss of control, resulting in personal injury.
□ Wear ear protectors when drilling. Exposure to noise can cause
hearing loss.
□ Secure your workpiece with a clamping device. A workpiece
clamped with clamping devices or in a vice is held more secure
than by hand.
□ Always wait until the product has come to a complete stop
before placing it down. The tool insert can jam and lead to loss
of control over the power tool.
□ Do not open the battery. Danger of shortcircuiting.
□ Protect the battery against heat, e.g., against continuous
intense sunlight, fi re, water, and moisture. Danger of explosion.
□ In case of damage and improper use of the battery, vapours
may be emitted. Provide for fresh air and seek medical help in
case of complaints. The vapours can irritate the respiratory system.
□ Use the battery only in conjunction with your Würth power
tool. This measure alone protects the battery against dangerous
overload.
□ Use only original Würth batteries with the voltage listed on
the nameplate of your power tool. When using other batteries,
e. g. imitations, reconditioned batteries or other brands, there is
danger of injury as well as property damage through exploding
batteries.
□ Use only original Würth accessories.
Residual Risks
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The operator should
pay particular and additional attention to these points in order to
reduce the risk of serious personal injury.
□ Injury to hearing – Wear suitable ear protection and limit
exposure.
□ Injury to sight – Wear protective eye shields or goggles when
using the product.
□ Injury caused by vibration – Limit exposure and follow the
instructions on risk reduction in this manual.
□ Electric shock after contact with hidden wires – Hold the product
only by insulated surfaces.
□ Respiratory injury from dust created by operating the product –
Wear suitable protection depending on type of dust.
Tool Specifi cations
Cordless drill driver
Article number
Voltage
Chuck
No load speed (drill mode)
Gear 1
Gear 2
Clutch (positions)
ABS 18 COMPACT
5701 427 000
18 V
1.5 - 13 mm
0-600 min
-1
0-1900 min
-1
18 + drill mode
14
Publicidad
