Publicidad
Idiomas disponibles
Idiomas disponibles
12 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........
Volts
n
.......
0
A ........
Amperes
FEATURES (Fig. A)
1. Slider switch
2. Cable
3. Tool free guard
4. Body grip
5. Side handle (2 positions)
6. Spindle lock button
Hertz
...... Class II
Watts
....
minutes
.....
Alternating
....
Current
.....
Direct
.../min..
Current
No-Load
Speed
ADDITIONAL SAFETY INSTRUCTIONS
FOR SMALL ANGLE GRINDERS
f Use the guard and ensure it is fitted correctly.
f Check mounting flanges and the disc are correctly
fitted and are undamaged.
f Ensure you are using the correct size and type of disc
for the task.
f Ensure the disc, wire brush and sanding accessories
are rated in excess of the spindle rpm of your angle
grinder. Allow a newly assembled wheel to idle off-
load for 30 seconds before starting any operation.
a. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
b. Operations such as cutting-off, sander, wire
brush or polisher are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
c. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can
be attached to your power tool, it does not assure safe
operation.
d. The rated speed of the accessory must beat least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
e. The outside diameter and the thickness of your
accessory must be within the capacity rating of
Construction
your power tool. Incorrectly sized accessories
Earthing
cannon be adequately guarded or controlled.
Terminal
f.
The arbour size of wheels, flanges,backing pads
Safety Alert
or any other accessory must properly fit the
Symbol
spindle of the power tool. Accessories with arbour
Revolutions
or Recipro-
holes that do not match the mounting hardware of the
cation per
power tool will run out of balance, vibrate excessively
minute
and may cause loss of control.
g. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive wheel
for chips and cracks, backing pad for cracks, tear
or excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing an
accessory, position yourself and by standers
SAFETY INSTRUCTIONS FOR
ALL OPERATIONS
Publicidad
