Manuales relacionados para Truper SOIN-130/200
Resumen de contenidos para Truper SOIN-130/200
- Página 1 Manual Inverter Welder Work Cycle Applies for: Code Model 16053 SOIN-130/200 SOIN-130/200 Read this manual thoroughly CAUTION before using the tool.
- Página 2 LED light ALARM on. Let the welder cool for 15 minutes and turn it back on. SOIN-130/200 It is recommended to use a 12 AWG extension cord and connect it to an INDEPENDENT CHARGING CENTER.
- Página 3 Technical specifications SOIN-130/200 Code 16053 Description Inverter Welder Input Power 127 V 220 V Bi-Voltage automatic adaptation system Frequency 50 Hz / 60 Hz Current 39.5 A 45 A No. of Phases 1 phase 2 phase Output Input Rated Capacity 5.0 kVA...
- Página 4 General Power Tools Safety Warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
- Página 5 Safety Warnings for Inverter Welders Protection Equipment for Welding Prevent Injuries and Accidents WARNING WARNING • Wear a welding mask to protect eyes • Risks of electric shock: and face when soldering. Assure the mask protective glass An electric shock coming from the soldering electrode may shade is adequate for the soldering process to carry out.
- Página 6 Parts Transportation Handle Thermal Protection Light Work Piece light Grounding Clamp Current Adjustment Control Positive Connection ( + ) Welding Electrode Process Holder Selector Negative (SMAW or TIG) Connection ( - ) Switch Carrying Strap Hammer-Brush for Slag Removal Power Protective Mask Cord...
- Página 7 Installation (SMAW) Connections CAUTION To prevent electric shock, you need to see information in section “Electrical Requirements” in pages 3 and 5. • The fast connections of the electrode holder and the grounding clamp are inserted and turned, one-quarter of a turn in a clockwise direction in the front panel output to get them properly secured.
- Página 8 Installation (TIG) TIG Connection • This inverter welder can also be used to TIG welding. It is a high-quality soldering with non- consumable tungsten electrodes and arc protected by inert gas like Argon or Helium. • TIG welding is ideal for welding stainless steel, iron and copper. •...
- Página 9 Start Up Preparation • Only experience, practice and care can guarantee a good welding job. • The factor intervening in the welding process are many: required current, distance between the electrode and the 45° 45° work piece, soldering speed and direction, thickness and type of the material, the work piece position, electrode angle and also gauge, type of material and electrode 60°...
- Página 10 Start Up Examples of welding Correctly Applied Welding Electrode movement too fast and / or very low current. Electrode movement too slow and / or very high current. Electrode too separated from the work piece. Spiral movement. Half-Moon movement. Bevel Zigzag Movement.
- Página 11 Maintenance • The correct use and regular cleansing extend the useful life of the welder. CAUTION • Only qualified personnel shall carry out repairs. We recommend visiting a Authorized Service Center to repair your welder, get supplies or accessories. Regular Maintenance Storage •...
- Página 12 Troubleshooting Problem Cause Solution The thermal protection • The welder has no adequate ventilation. • Keep the welder least 11.8” away from any walls at to light is ON. allow air circulation. • Environment temperature is too high. • The welder will recuperate once the temperature gets back to the right range to operate.
- Página 13 Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center.
- Página 14 . Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.