Publicidad
ELECTRONIC UNIT LXB 2102 NEW
Single-phase electronic control unit for the automation of sliding
gates, garage doors with incorporated Bluetooth module 5.0,
radio receiver included on Module DIN Rail Plastic Box.
- Mod. LGB 2102 NEW
- Mod. LSB 2102 NEW
- Mod. LHB 2102 NEW
I
MPORTANT FOR THE USER
- The device can be used by children over 8 years of age
and persons with reduced physical or psychological
abilities or with little knowledge and experience only if
supervised or educated in its operation and safe use, in
order to also understand the dangers involved in its use.
- these instructions are also available at the website
http://www.seav.it/
- Do not allow children to play with the device and keep
the radio controls away from their reach.
- Frequently examine the system to detect any signs of
damage. Do not use the device if it is in need of repair
work.
-Always remember to disconnect the power supply before
carrying out any cleaning or maintenance.
- Cleaning and maintenance must not be carried out by
unsupervised children
- ATTENTION: keep this instruction manual safe and
observe the important safety requirements contained
herein. Failure to comply with the requirements may
cause damage and serious accidents.
I
the
MPORTANT FOR
INSTALLER
15) Before automating the gate, check that it is in good
conditions, in compliance with the Machinery Directive
and with EN 12604.
16) Check that the location where the installation is
located enables compliance with operating temperature
limits specified for the device.
17) The safety of the final installation and compliance
with all prescribed Standards (EN 12453 - EN 12445) is
the responsibility of the person who assembles the
various parts to construct a total closing.
18) It's recommended to use safety devices with a
connection self test.
19) Once installation is finished, it is recommended that
all
necessary
checks
programming of the control panel and correct installation
of safety devices) to ensure that compliant installation
has been performed.
20) The control unit does not have any type of isolating
device for the 230 Vac line. It is therefore the
responsibility of the installer to set up an isolating device
inside the system. It is necessary to install an omnipolar
switch, surge category III. It must be positioned to
provide protection from accidental closing, pursuant to
point 5.2.9 of EN 12453
21) Cables for power and connection to the motor must
have an outside diameter between 4.5 and 7 mm. The
internal conductor wires must have a nominal section of
0.75mm2. If a raceway is not used, use H05RR-F
: without receiver
: 433,92 Mhz "narrow band"
: 868,3 Mhz "narrow band"
be
performed
(appropriate
cables. Pay careful attention when fastening the cables
GB
so that they are anchored in a stable manner.
8) The gearmotor used to move the frame must comply
with that prescribed at point 5.2.7 of EN 1245
9) In compliance with 5.4.2 of EN 12453, it is
recommended to use gearmotors equipped with an
electric-mechanical release device, so that the door can
be moved manually in case of necessity.
10) In compliance with 5.4.3. of EN 12453, use electric-
mechanical release systems or similar devices which
stop the door safely in the end run position.
11) The various electrical components external to the
control unit must be cabled in accordance with standard
EN 60204-1 as amended, and as set forth in point 5.2.7
of EN 12453.
12) The assembly of a push button panel for manual
control must be completed positioning the push button
panel in such a way that the user is not placed in a
dangerous position.
13) The safety function ensured by the control unit is
active only during closing, therefore, protection on
opening must be ensured in the installation phase with
measures (guards or safety distances) independent of
the control circuit.
14) For proper functioning of the radio receiver, if using
one or more control units, the installation at a minimum
distance of at least 3 metres one from the other is
recommended.
Electronic Control Units:
LGB 2102 NEW – LSB 2102 NEW –
comply with the requirements of Directives
RED 2014/53/EU, EMC 2014/30/EU, LVD
The full text of the EU declaration of conformity is available at
the following Internet address:
http://www.seav.it/
5
The below products:
LHB2102 NEW
2014/35/EU.
rev. 1.0 01/06/2021
Publicidad
