Implementación Midi; Transmitted Data - Roland V-Accordion FR-1X Manual Del Usuario

FR-1x V-Accordion
Apéndice
Implementación MIDI
1. Received data
I Channel Voice Messages
G Note off
Status 2nd byte
8nH kkH
n = MIDI channel number:
kk = note number:
vv = note off velocity:
G Note on
Status 2nd byte
9nH kkH
n = MIDI channel number:
kk = note number:
vv = note on velocity:
G Control Change
• The value specified by a Control Change message is not reset by a Program
Change, etc.
H Bank Select (Controller number 0, 32)
Status 2nd byte
BnH 00H
BnH 20H
n = MIDI channel number:
mm = Bank number MSB:
ll = Bank number LSB:
• Only for Free Bass.
H Expression (Controller number 11)
Status 2nd byte
BnH 0BH
n = MIDI channel number:
vv = Expression:
• This adjusts the volume of a Part. It can be used independently from Volume
(CC07) messages. Expression messages are used for musical expression within
a performance, e.g., expression pedal movements, crescendo and decrescendo.
H Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number:
pp = Program number:
I System Realtime Messages
H Active Sensing
Status
FEH
• When Active Sensing is received, the FR-1x starts monitoring the intervals of all
further messages. While monitoring, if the interval between messages exceeds
420 ms, the same processing will be carried out as when All Sounds Off, All Notes
Off and Reset All Controllers are received, and message interval monitoring will
be halted.

2. Transmitted data

I Channel Voice Messages
G Note off
Status 2nd byte
8nH kkH
n = MIDI channel number:
kk = note number:
vv = note off velocity:
G Note on
Status 2nd byte
9nH kkH
n = MIDI channel number:
kk = note number:
vv = note on velocity:
G Control Change
H Bank Select (Controller number 0, 32)
Status 2nd byte
BnH 00H
BnH 20H
n = MIDI channel number:
mm = Bank number MSB:
ll = Bank number LSB:
72
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
00H~7FH (0~127)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
01H~7FH (1~127)
3rd byte
mmH
llH
0H~FH (Ch.1~16)
00H~7FH
00H~7FH
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
0H~FH (Ch.1~16)
See "3. Program change messages".
For the Sets, see "SET RX" en la pág. 73
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
00H~7FH (0~127)
3rd byte
vvH
0H~FH (Ch.1~16)
00H~7FH (0~127)
01H~7FH (1~127)
3rd byte
mmH
llH
0H~FH (Ch.1~16)
00H~7FH
00H~7FH
H Modulation number (Controller number 01)
Status 2nd byte 3rd byte
BnH 01H vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
vv = Modulation depth: 00H~7FH (0~127)
H Volume (Controller number 7)
Status 2nd byte 3rd byte
BnH 07H vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
vv = Volume: 00H~7FH (0~127)
• Volume messages are used to adjust the level of the Orchestra, Organ and Drum
parts.
H Pan (Controller number 10)
Status 2nd byte 3rd byte
BnH 0AH vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
vv = Pan: 00H~40H~7FH (0~127) (left–center–right);
Initial value: 40H (center)
• The stereo position can be adjusted in 127 steps.
H Expression (Controller number 11)
Status 2nd byte 3rd byte
BnH 0BH vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
vv = Expression: 00H~7FH (0~127)
• This adjusts the volume of a Part. Expression messages are used for musical ex-
pression within a performance, e.g., expression pedal movements, crescendo and
decrescendo.
H Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H~FH (Ch.1~16)
pp = Program number: 00H~7FH: program no. 1~128
H Pitch Bend Change
Status 2nd byte 3rd byte
EnH llH mmH
n = MIDI channel number: 0H~FH (Ch.1~16)
mm, ll= Pitch Bend value 00 00H~40 00H~7F 7FH (–8192~0~+8191)
H Effect 1 (Reverb Send level; Controller number 91)
Status 2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
vv = Reverb Send level: 00H~7FH (0~127)
• This message adjusts the Reverb Send level of all parts.
H Effect 3 (Chorus Send level; Controller number 91)
Status 2nd byte 3rd byte
BnH 5DH vvH
n = MIDI channel number: 0H~FH (Ch.1~16)
vv = Reverb Send level: 00H~7FH (0~127)
• This message adjusts the Chorus Send level of all parts.
I System Realtime Messages
H Active Sensing
Status
FEH Transmitted about every 250ms.
H Start
Status
FAH This message is transmitted when the [METRONOME] switch is
pressed after assigning the "2" option to the "MFn" parameter.
H Stop
Status
FCH This message is transmitted when the [METRONOME] switch is
pressed after assigning the "2" option to the "MFn" parameter.
3. Program change messages
CC00 CC32 Program
Change
TREBLE REGISTER TX/RX
0 0 1
0 0 2
0 0 3
0 0 4
0 0 8
0 0 5
0 0 6
0 0 7
Register Name
1a Bassoon
1b Bandon
1c Cello
1d Harmon
2a Master
2b Organ
2c Accord
2d Violin