Publicidad
Idiomas disponibles
Idiomas disponibles
Installation and moving
Your dishwasher has arrived
After having bought or moved your dishwasher to another home, a
correct installation ensures that your dishwasher will operate
smoothly and efficiently.
Choose where you want to
install your dishwasher,
you can even place it so that
its sides or back panel are
side by side with furniture
or up against the wall. The
dishwasher is provided with
water supply and drain
hoses, which can be directed
towards the left or right to
facilitate
appropriate
installation.
Levelling.
Once the appliance is
positioned, adjust the feet
by screwing them in or out
depending on how high you
want it and to level it so that
it is horizontal. Make sure
that it is not inclined more
than 2 degrees. If the
appliance is level, it will he
lp
ensure
its
correct
operation.
Adjusting the Back Feet
Insert the appliance into the
cutout and then adjust the
height using the screws
located on the front bottom
part of the machine. Use a
screwdriver to turn the
screws in the clockwise or
anti-clockwise direction to
increase or decrease the
height respectively.
Cold water connection.
Connect the cold water
supply hose to a threaded 3/
4 (gas) connector,
and
making sure that it is
fastened tightly in place.
The LV460 A model, have
a "Water Stop" water
supply pipe.
If the water pipes are new
or have not been used for an
extended period of time, let
the water run to make sure
that the water is clear and
free of impurities. If this
precaution is not taken,
there is a risk that the
water inlet can get blocked
and damage the appliance.
-It is strongly recommended
to use a new hose to connect
the dishwasher to the water
supply line, and the old
hose-set should not be
reused. Asking to specilized
shop or an authorized
service technician (see
Service).
Hot water connection.
Your dishwasher can be
supplied with hot water
from the mains supply (if
you have a central heating
system with radiators) at a
temperature of no more
than 60°C.
In this case, the wash cycle
time will be about 15
minutes shorter and the
wash will be slightly less
effective.
The connection must be
made to hot water supply
following
the
same
procedures
as
those
indicated for the cold water
connection.
Anti-flooding
protection
Your dishwasher (model LV
460A) is provided with a
special system which blocks
the water supply in the
event of leaks inside the ap-
pliance.
It
is
further
equipped with a water inlet
hose ("WATER STOP")
that can withstand ex-
tremely high pressures and
that turns bright red in the
event of breakage. Safety in
the event of flooding is
ensured by the second clear
hose that contains the
former and thus highlights
the latter when it has
turned bright red. It is vital
that you check it on a
regular basis: if you see it
has turned bright red, then
you know you have to
replace it as soon as
possible.
Call
for
authorised
technical
engineer to come and
replace it.
Drain hose connection.
Fit the drain pipe into a
drain line with a minimum
diameter of 4 cm or place it
over
the
sink.
Avoid
restricting or bending it.
The part of the pipe marked
with the letter A should be
between 40 and 100 cm
above the ground.
The pipe should not be
immersed in water.
Condensation-proof tape.
On
some
models,
transparent condensation-
proof adhesive tape has been
provided.
It should be stuck onto the
lower side of your wooden
worktop to protect it from
the
formation
condensation.
When not provided, this tape
can be requested as a spare
part
from
authorised
retailers.
Electrical connection.
First of all, check that the
mains
voltage
frequency
correspond to those stated
on the rating plate located
on the stainless steel inner
door of the appliance and
that the electrical system to
an
which the dishwasher is
connected is sized for the
maximum
indicated on said rating
plate.
ARISTON DISHWASHER - Instructions for installation and use
D
1509)50-4
Earth: indispensable
A
safety.
Only now can you plug the
appliance into a socket
provided with an efficient
earth
connection
system's earthing is a
guarantee of safety provided
for by law, make sure your
system has it).
Attention
a
- Once the appliance has
been installed, the electrical
plug and socket should re-
main accessible.
- If the power supply cable
is damaged, it must be
of
replaced
manufacturer
Technical
Service in order to prevent
all potential hazards. (See
Assistance)
- The cable should not be
bent or compressed.
and
- The Company shall not be
values
held responsible for any
incidents that occur if these
regulations are not
observed.
current
If the power socket to
which the appliance is
connected is not
compatible with the
plug, replace it with a
suitable plug rather
than using adapters or
multiple plugs as these
could cause
overheating or burns.
(the
by
the
or
its
Assistance
19
Publicidad
