Descargar Imprimir esta página

DeWalt DW955 Manual De Instrucciones página 8

Taladro/destornillador inalambrico angulo recto
Ocultar thumbs Ver también para DW955:

Publicidad

Idiomas disponibles

Idiomas disponibles

shock may r esult. To facilitate
the cooling ofthe battery pack a fter
use,avoid placing t hecharger or battery p ackin a warm
_,environment
such a sinametal shed, oranuninsulated
trailer.
ZL_ CAUTION:
Never attempt toopen t he battery pack forany reason.
Ifthe plastic housing
ofthe battery pack b reaks orcracks, return to
aservice center forrecycling.
Operation
Variable
Speed
Paddle
Switch
(FIG. 4-A)To turn the tool on, squeeze the paddle switch. To turn the
tool off, release the paddle switch. Your tool is equipped with a brake.
The chuck will stop as soon as the paddle switch is fully released.
The variable speed switch enables you to select the best speed for a
particular application. The farther you squeeze the paddle, the faster
the tool will operate.
Use lower speeds for starting holes without a
centerpunch,
drilling in metals or plastics, driving screws and drilling
ceramics, or in any application
requiring high torque. Higher speeds
are better for drilling
in wood, wood compositions
and for using
abrasive
and polishing
accessories.
For maximum
tool life, use
variable speed only for starting holes or fasteners.
NOTE: Continuous use in variable speed range is not recommended.
It may damage the switch and should be avoided.
Forward/Reverse
Control
Button
(FIG. 4-B) A forward/reverse
control button determines the direction of
the tool and also serves as a lock off button
To select forward rotation, release the paddle switch and depress the
forward/reverse
control button on the right side of the tool .To select
reverse, depress the forward/reverse
control button on the left side of
the tool. The center position of the control button locks the tool in the
off position. NOTE: When the tool is not in use or being transported,
keep the button in the middle lock position
When changing the position of the control button, be sure the paddle
is released.
NOTE: The first time the tool is run after changing
the
direction of rotation, you may hear a click on start up. This is normal
and does not indicate a problem.
Dual
Range
Gearing
(FIG. 4-C) The dual range feature of your Drill/Driver allows you to shift
gears for greater versatility.
To select the low speed, high torque setting, turn the tool off and permit
to stop. Slide the gear shifter forward (towards the chuck). To select the
high speed, low torque setting, turn the tool off and permit to stop. Slide
the gear shifter back (away from chuck).
NOTE Do not change gears when the tool is running. If you are having
trouble changing gears, make sure that the dual range gear shifter is
either completely pushed forward or completely pushed back.
Keyless
Chuck
Your tool features
a 3/8" keyless chuck for greater convenience.
To
insert a drill bit or other accessory, follow the steps listed below.
1. Lock the trigger switch in the off position as described on page 6.
2. Grasp the rear half of the chuck with one hand and use your other
hand to rotate the front half counterclockwise.
Rotate far enough
so that the chuck opens sufficiently to accept the desired accessory.
3. Insert the bit or other accessory
about 3/4" into the chuck and
tighten securely by holding the rear half of the chuck and rotating
the front portion in the clockwise direction.
To release the accessory, repeat step 2 listed above.
Z_ WARMNG:
Do not attempt
to tighten
drill bits (or any other
accessory) by gripping the front part of the chuck and turning the tool
on. Damage to the chuck and personal injury may result. Always lock
off trigger switch when changing accessories.
Be sure to tighten chuck with two hands on both the rear sleeve and
the forward sleeve for maximum tightness.

Publicidad

loading

Este manual también es adecuado para:

Dw965Dw966