Publicidad
Idiomas disponibles
Idiomas disponibles
English
Intended Use
The DWAPXCIR is designed to install copper crimp rings that
meet ASTM F1807 requirements. Only trained personnel
should operate this tool.
The DWAPXCIR is designed for use with impact drivers
that have an operating speed less than 4,000 RPM and a
maximum torque rating of less than 280 Nm (2,500 in-lb). If
using with a higher performing impact driver, select a mode
which has a speed of less than 4,000 RPM and maximum
torque rating that is less than 280 Nm (2,500 in-lb).
DO nOT use this attachment with drill/driver. This
attachment is approved only for use with an impact driver.
DO nOT use in the presence of flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert
symbols and words to alert you to hazardous situations and
your risk of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous
situation which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in minor or
moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
Safety Rules for PEX Crimp Ring Press Attachment
WARNING: Read and understand these instructions
and those for the attached power tool. Before use, ensure
the attachment is properly attached to the tool.
WARNING: Use the PEX crimp ring press attachment
only with D
WALT or D
E
E
Other uses or modifying the attachment for other
applications may damage the attachment, damage the
accessories and/or can result in a faulty installation.
Faulty installation can result in failures, injury to installers and
damage to property.
WARNING: When using this PEX crimp ring press
attachment for installing fittings, the preparation of
the cut and installation of the fitting should follow
recommendations from the fitting manufacturer for
proper installation procedures. Proper preparation and
installation is the responsibility of the installer.
• Only trained personnel should operate this tool.
• Keep all body parts away from the attachment during
operation and any time the power is ON. A moment of
inattention while operating power tools may result in
serious personal injury. Fingers or hands can be crushed,
fractured or amputated if they become caught in the attachments.
• Inspect tool and attachments before use for any
loose or missing parts. Never attempt to repair or use a
damaged PEX crimp ring press attachment, brace or other
attachment. Replace with a new press attachment or brace.
4
WALT-approved accessories.
• This tool produces large forces that can break attachments
or parts and cause injury. Always be attentive and take proper
safety precautions, including wearing eye protection.
• Before operating, inspect job site for hazards including
chemicals or waste that can remain in pipes.
• Before operating, read and understand all safety
and operating instructions including the fitting
manufacturer's installation instructions and the
instructions for any other equipment used with this tool.
Failure to follow all instructions and warnings may result in
property damage and/or serious personal injury.
• Keep the working area of the attachment free from
hands and other objects while the tool is in use. Fingers
could be crushed.
• Secure and support the material prior to making the
press to prevent movement during pressing.
• Pressing operations may cause material pieces to fly.
Flying particles can cause permanent eye damage. Always
wear eye protection.
• Always wear gloves when operating tool and handling
materials. The ends of materials can be sharp and cause
serious personal injury.
Additional Safety Information
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or dust
mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead‑based paints,
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically‑treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or
lay on the skin may promote absorption of harmful chemicals.
Direct particles away from face and body.
• Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to the
operator and those in close proximity.
• Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may lead
to loss of control and injury.
Publicidad
