Publicidad
Idiomas disponibles
Idiomas disponibles
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving parts.
CAUTION: When not in use, place tool on its side on a
stable surface where it will not cause a tripping or falling
hazard. Some tools with large battery packs will stand upright
on the battery pack but may be easily knocked over.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V .......................... volts
Hz ........................hertz
min ......................minutes
or DC ......direct current
....................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per minute
RPM .................... revolutions per minute
sfpm ................... surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, DO
NOT use the universal brace bracket or brace arm for tethering or
securing the tool to a person or object during use when elevated.
WARNING: To reduce the risk of serious personal
injury, remove the battery pack before making any
adjustments, removing/installing the brace bracket,
attachments, or accessories, and while transporting. An
accidental start up can cause injury.
WARNING: Never modify this device or any part of it.
Damage or personal injury could result.
Attaching the Universal Brace Bracket (Fig. B–D)
1. Remove the battery from your impact driver.
nOTE: DO nOT reinstall the battery until AFTER the brace
bracket is installed.
2. Loosen the back knob
open wide enough to slip the impact driver through as shown
in Fig. B.
3. Slide the impact driver into the brace bracket from the top
as shown in Fig. C.
4. Place the impact driver and brace bracket on a FlAT surface.
5. Compress the front end together until the brace bracket
is snug around the impact driver foot, then tighten the back
knob. Both sides should remain parallel during tightening as
shown in Fig. D.
Attaching the Brace Arm and Impact Connect
Attachment (Fig. E–G)
1. Loosen both of the yellow arm knobs
insert the attachment shank
chuck
as shown in Fig. E.
13
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all documentation
..................... do not expose to rain
until the brace bracket
1
2
3
one turn and
4
into the impact driver
2. Rotate the arm joint
bar
clicks into the bar channel
7
audible clicking as you rotate. The yellow slide lock
should secure the bar in place as shown in Fig. F.
3. Ensure the shank is parallel to the ground and finger
tighten all knobs as shown in Fig. G.
4. Reinstall the battery AFTER installation and prior to use.
Scan QR code for installation video.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
WARNING: Proper material preparation
and installation is the responsibility of the
installing contractor.
WARNING: The tubing and hardware must be used
in compliance with applicable building codes and as
approved by the authorities having jurisdiction. For
proper installation procedures and to reduce the risk of failure
resulting in injury or property damage, follow all published
safety and installation instructions.
CAUTION: Pinch hazard. Keep fingers away from the jaws
while in use.
The DWAPXCIR PEX crimp ring press attachment uses a
compatible impact driver to actuate a power screw which
mechanically compresses a crimp ring.
Forward setting:
‑ Squeezing the trigger with the impact driver set to forward
(clockwise) advances the cam and compresses the jaws.
‑ Fully releasing the trigger switch stops the
can
advancement of the mechanism.
Reverse setting:
‑ Squeezing the trigger with the impact driver set to
reverse (counterclockwise) will open the jaws.
‑ Fully releasing the trigger switch stops the retraction
of the mechanism.
WARNING: CRUSH HAZARD. Keep fingers away
from clamping area. Failure to do so can cause injury.
WARNING: Proper material preparation and installation is
the responsibility of the installing contractor.
5
and the arm slider
6
until the
. There will be an
8
English
9
5
Publicidad
