Publicidad
Idiomas disponibles
Idiomas disponibles
Charging current for USB
Weight
NOTE
○ The recharging time may vary according to the ambient
temperature and power source voltage.
○ If charging takes a long time
–
Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
–
Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
–
If the cooling fan is not operating, contact a HiKOKI
Authorized Service Center for repairs.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
AC adaptor / DC cord installation*
About the switch panel
Turn the power ON*
2
Select the partitioning mode*
Setting the temperature*
How to use partitions*
5
Charging the battery on the cooler and
warmer storage*
6
Charging a USB device on the cooler
and warmer storage*
7
2 A
0.6 kg
Figure
2
3
1
4
5
6
3
7
4
8
9
10
11
Using as a DC 12 V power source*
How to attach the shoulder belt
Remaining battery indicator (on
battery)
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
Selecting accessories
*1 Use AC adapter / DC cord
NOTE
○ When used together with the batteries, the AC adapter
or the DC code is the main power source and no battery
power is consumed.
○ Make sure that the connection plug is inserted all the
way. If incorrectly inserted, the appliance could
overheat and result in damage.
○ When using a car as power source, connect while the
engine is running. It can cause the battery to die.
○ When a car equipped with an auto start-stop function
has its engine stopped, the voltage of the car's battery
decreases, so the warming/cooling function of the
appliance may stop. It is recommended to use the
appliance with the car's auto start-stop function turned
OFF.
○ When the power plug is plugged into an outlet when a
battery is installed, the battery will charge whether the
power switch is ON or OFF.
○ Power Supplied Automatic Restoration Function
When this function is turned ON, if the power supply
that is providing power is shut off, even if the battery
isn't installed, when power is supplied again, the power
of the cooler and warmer storage is automatically
restored to the ON state.
–
Press and hold the power switch for 3 seconds or
longer.
–
The power supplied lamp lights up, and then
changes to blinking.
HINT
Even when using with an in-car power source, it is
recommended to attach the battery.
While the engine is turned off, the power source switches to
Page
the appliance's battery and it continues cooling/warming.
When the engine is started again, the power source
231
switches to the car's battery, and the appliance's battery
starts charging at the same time.
231
If the Power Supplied Automatic Restoration Function is
ON, when the engine restarts, the cooling/warming function
231
automatically resumes at the same time for convenience.
*2 Turn the power ON
232
The temperature that was set the previous time is displayed
for about 5 seconds, then the display changes to the
232
temperature inside the compartment, and operation starts.
232
NOTE
Do not press the power switch repeatedly. Doing so
233
may cause a malfunction.
After configuring settings, wait about 5 minutes before
233
pressing it again.
*3 Select the partitioning mode
233
A: 1 Zone Mode
B: Left Zone Mode
C: Right Zone Mode
234
D: 2 Zones Mode
9
Action
Figure
8
English
Page
12
234
13
234
15
235
16-a
235
16-b
235
17
235
—
237
Publicidad
