Toa WM-5325 Instrucciones De Uso página 5

8. CHANNEL NUMBER/BANK SETTING
Step 1. Turn off the power switch, and then remove the battery
cover.
Step 2. Using the supplied screwdriver, set the Channel setting
switch pointers to the desired channel number/bank.
Step 3. Replace the battery cover.
Note
Make sure that the wireless transmitter is identical to the wireless
tuner in the channel number/bank. Should the
setting differ from that of the tuner, the tuner does not receive the
microphone signal.
9. OPERATION
Step 1. Plug the microphone's plug into the input connector as illustrated.
Step 2. Confirm that the wireless transmitter
If not identical, turn the power ON/OFF switch to the OFF position, then set the channel
to the same one as the tuner.
Step 3. Turn the Power ON/OFF switch to the ON position. Then, confirm the green LED of the Power/Battery
lamps will light.
When using with the WH-4000P Waist
below.
Step 4. Turn the Power ON/OFF switch to the OFF position after use.
WM-5325
1
Plug lock
Secure the connection with the plug lock.
8
Channel setting switch
transmitter's
and the wireless tuner are identical in the channel number/bank.
Pouch, put the unit into the waist pouch as shown in the figure
WH-4000P
Hook and loop fastener
Belt
3
Plug lock
10. OPERATIONAL HINTS
• The transmitter's
dropouts (momentary losses of signal reception) may be encountered. These dropouts are caused by the
building's architectural designs or materials which block the travel of or reflect the radio signal. If this occurs,
the user needs to change locations for better signal reception.
• The proper operation of your wireless system may be interfered with by other system operating on the same
frequency. In such cases, change the operating frequency of your system. (As to dealing with the
interference, refer to the operating instructions of the wireless tuner.)
• Should you have any questions regarding the use or availability of TOA wireless products, please contact
your local TOA dealer.
11. DISTANCE BETWEEN THE MICROPHONE AND THE MOUTH
[YP-M5300 and YP-M5310 Lavalier Microphones]
Keep your mouth 15 – 20 cm away from the microphone for the best possible sound reproduction. Take care
not to bring your mouth too close to the microphone (within 5 cm) as this impairs speech clarity if you speak
loudly.
[WH-4000A and WH-4000H Headset Microphones]
By adjusting the gooseneck, locate the microphone with the supplied windscreen in front of your mouth, and
position it 3 – 5 cm away from your mouth for the best sound reproduction. When the microphone is too close
to your mouth or you speak too loud, speech clarity will be impaired, making it hard for the audience to hear
announcements.
12. AUDIO LEVEL ADJUSTMENT (SENSITIVITY CONTROL)
To change the factory-preset level, follow the procedures below.
number/bank
Step 1. Holding the
illustrated.
Step 2. Switch on the power of the tuner and transmitter.
Step 3. Adjust the audio level control using the supplied
screwdriver. The
control is rotated clockwise, and decreases as rotated
counterclockwise.
Step 4. Adjust the corresponding tuner's volume control so that
its knob points to the 2 o'clock position. If the tuner's AF
peak lamp remains lit, readjust the
indicator to flash when the tuner output level reaches its peak. The AF peak lamp lights when the
output level reaches the point of about 3 dB below the clipping level.
Note
The AF peak lamp operates in response to the volume control position.
However, the AF level lamp on the LCD (on the WT-5800/5805) indicates the level regardless of the
volume control setting.
Step 5. Replace the
service distance is 3 – 120 m. When the transmitter
transmitter body, open the rubber cap as
transmitter sensitivity increases as the
transmitter's audio level control to the position that causes the
rubber cap.
user moves in a facility, signal
2
Power ON/OFF
switch
3
Audio level control
1
9