Audibax ADP 24 DSP Manual De Usuario página 5

PACKAGE CONTENT
1 x ADP 24 DSP / ADP 36 DSP / ADP 48 DSP
1 x User's manual
1 x Power cord
SPECIFICATION
Model
Number of entries
Number of outputs
Input Impedance
Output impedance
Control interface:
USB/RS232/Ethernet/Wi -Fi
Common simulation
system ratio
Input sensitivity
Frequency response
Signal to noise ratio
Distorsion Armonica
Separacion entre canales
Mute
Delay
Input Polarity
channel
Parametric
Equalizer
Mute
Input
Gain
Delay
Polarity
Parametric
Output
Equalizer
channel
Frequency
Divider
Limiter
Processor Type
Energy consumption
Power supply
Net weight
Packing size
www.audibax.com
ADP 24 DSP / ADP 36 DSP / ADP 48 DSP
ADP 24 DSP
2 XLR Female inputs
4 Male XLR Outputs
(Canon)
Balance: Ω 20 k
Balance:100 Ω
Panel 1 USB interface
＞70dB(1KHz)
≥＋12dBu
20Hz-20KHz(-0.5dB)
＞105dB
<0.01% OUTPUT=0dBu/1KHz
>80dB(1KHz)
Input mute control for each channel
Each input channel has an individual delay control, the adjustment range is
1000ms, less than 10ms, the step distance is 21 μs; > 10ms, the step distance is
1ms
In phase(+) & reversed phase( -)
8 parameters are set for each input channel. Adjusting parameters under PEQ
are: center frequency point: 20Hz-20KHz,Q value: 0.404 -28.85, step distance:
0.002 OCT gain: -20dB~+12dB step distance: 0.1dB Lo -shel, Hi -shel, center
frequency point: 20Hz -20KHz, Q value is not adjustable; Gain: -20dB~+12dB
Step is 0.1dB
Output mute control for each channel
Each output channel can select from the number of available inputs
Adjusting range: +12dB to -36dB, step is 0.1dB
Each input channel has an individual delay control, the adjustment range is 0 -
1000ms, less than 10ms, the step distance is 21 μs; > 10ms, the step distance is
1ms
In phase(+) & reversed phase( -)
8 parameters can be set for each output channel. Adjusting parameters under
PEQ are: center frequency point: 20Hz -20KHz,Q value: 0.404 -28.85, step
distance: 0.002 OCT gain: -20dB~+12dB step distance: 0.1dB Lo -shel, Hi -shel:
Center frequency point: 20Hz -20KHz, Q value can not be adjusted; Gain: -
20dB~+12dB Step is 0.1dB
Each output channel can be individually configured with a low -pass filter (LPF)
and a high-pass filter (HPF) filter type: LinkWitz -Riley /Bessel/Butterworth
Frequency turning point: 20Hz -20kHz attenuation slope :Bessel/Butterworth
12/18/24/36/48dB, LinkWit z-Riley 12/24/36/48 dB
Each output channel can be set separately limiter, adjustable parameters as:
threshold value: ±20dB μ, step distance: 1dB μ Start time: 0.3ms -100ms, less
than 1ms, step distance: 0.1ms; Release time: can be set as 2 times, 4
times, 8 times, 16 times, 32 times the starting time
96kHz sampling frequency, 32 -bit DSP processor, 24 -bitA/D and D/A
conversion
≤25W
AC 110V/240V 50Hz/60Hz
3kg
570×260×90mm
ADP 36 DSP
3 XLR Female inputs
(Canon)
6 Male XLR Outputs
(canon)
3
ADP 48 DSP
4 Female XLR Inputs
(Canon)
8 Male XLR Outputs
(canon)
0-
times, 6