Connecting The Water Line - LG LSC27935 Serie Manual De Usuario

Type 2 When using any electrical device (such as a power drill)
Adjusting fools: 5/16" (8 ram) wrench and 3/4" (19 ram) during installation, be sure the device is double insulated
wrench, or grounded in a manner to prevent the hazard of electric
shock, or is battery-powered. All installations MUST be in
accordance with local plumbing code requirements.
NOTE: Wear eye protection.
Using a 3/4" (19 ram) wrench, turn the keeper nut
clockwise to loosen the keeper nut.
Using a 5/16" (8 ram) wrench, turn the adjustment hinge
pin clockwise or counterclockwise to level the refrigerator
and freezer door.
If a reverse osmosis wafer filtration system is
connected to your cold water supply, the water line
installation is not warranted by the refrigerator or ice
maker manufacturer or seller. Follow next instruction
carefully to minimize the risk of expensive water
damage.
if a reverse osmosis wafer filtration system is
connected to your cold water supply, the water pressure
to the reverse osmosis system needs to be a minimum
of 40 to 60 PSI (0,28 MPa - 0,41 MPa), less than 2-3
sec to fill a cup of 7 oz. capacity. (0,2 L).
After setting level door, turn the keeper nut
counterclockwise to tighten.
CAUTION
Do not over tight the door adjustment screw. The
hinge pin can be pulled out. (Adjustable range of
height is a maximum of 1/2" (13 ram)).
AFTER LEVELING THE DOOR HEIGHT
Confirm all legs are in contact with the floor.
CONNECTING THE WATER LINE
NOTE: Water line installation is needed when the
Automatic Ice maker and/or Water Dispenser
features are available on your product.
BEFORE YOU BEGIN
This water line installation is not warranted by the
refrigerator or ice maker manufacturer or seller.
Follow these instructions carefully to minimize the risk of
expensive water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts
and lead to water leakage or flooding. Call a qualified
plumber to correct water hammer before installing the
water supply line to the refrigerator.
To prevent burns and product damage, do not hook up
the water line to the hot water line.
If you use your refrigerator before connecting the water
line, make sure the ice maker power switch is in the OFF
(0) position.
If the wafer pressure from the reverse osmosis system is
less than 21 PSI (0,14 MPa), more than 4 sec to fill a cup
of 7 oz. capacity (0,2L):
0 Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
0 Allow the storage tank on the reverse osmosis system to
refill after heavy usage.
0 If the issue about water pressure from reverse osmosis
remains, call a licensed, qualified plumber.
WHAT YOU WILL NEED
• Copper Tubing, 1/4" (6,35 mm) outer
diameter to connect the refrigerator to
the water supply. Be sure both ends of
the tubing are cut square.
To determine how much tubing you need, mea su re
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add S feet
(2,4 m). Be sure there is sufficient extra tubing (about
8 feet [2,4 m] coiled into 3 turns of about 10" [25 cm]
diameter) to allow the refrigerator to move out from the
wall after installation.
Be sure that the kit you select allows at least S feet
(2,4 m) as described above.
• A cold wafer supply. The water pressure MUST be
between 20 and 120 PSI (0,14 and 0,$3 MPa) on
models without a water filter and between 40 and 120
PSI (0,28 and 0,83 MPa) on models with a water filter.
• Power drill.
• 1/2" (13 ram) or Adjustable Wrench.
Do not install the ice maker tubing in areas where • Flat head and Phillips screwdrivers.
temperatures fall below freezing.
10