Intended Use - Makita DHS782 Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Blade diameter
Max. Cutting depth
No load speed
Overall length
Rated voltage
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for performing lengthways and
crossways straight cuts and miter cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine saw blades, other materials
can also be sawed.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-5:
Model DHS782
Sound pressure level (L
Sound power level (L ) : 104 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DHS783
Sound pressure level (L
Sound power level (L ) : 104 dB (A)
WA
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
at 0°
at 45° bevel
at 48° bevel
) : 93 dB(A)
pA
) : 93 dB(A)
pA
DHS782
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
WARNING:
WARNING:
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-5:
Model DHS782
Work mode: cutting wood
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: cutting metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DHS783
Work mode: cutting wood
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: cutting metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
10 ENGLISH
DHS783
185 - 190 mm
60.0 - 62.5 mm
43.0 - 44.5 mm
41.0 - 42.0 mm
-1
6,000 min
348 mm
D.C. 36 V
4.5 - 5.1 kg
Wear ear protection.
The noise emission during actual
Be sure to identify safety measures
2
) : 2.5 m/s or less
h,W
2
2
) : 2.5 m/s or less
h,M
2
2
) : 2.5 m/s or less
h,W
2
2
) : 2.5 m/s or less
h,M
2