Intended Use - Makita JR002G Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
L e n g t h o f s t r o k e
S t r o k e s p e r m i n u t e
M a x . c u t t i n g c a p a c i t i e s
O v e r a l l l e n g t h
R a t e d v o l t a g e
N e t w e i g h t
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
Specifications and battery cartridge may di er from country to country.
The weight may di er depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combinations, according to EPTA-Procedure 1/
Applicable battery cartridge and charger
Battery cartridge
C h a r g e r
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

T h e t o o l i s i n t e n d e d f o r s a w i n g w o o d , p l a s t i c a n d f e r -
r o u s m a t e r i a l s .
Noise
The typical A-weighted noise level determined accord-
ing to EN 8 1- -11:
Sound pressure level (L
Sound power level (L ) : 8 dB (A)
WA
Uncertainty (K) : dB(A)
NOTE: The declared noise emission value(s) has been
m e a s u r e d i n a c c o r d a n c e w i t h a s t a n d a r d t e s t m e t h o d a n d
may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
WARNING:
W ear ear protection.
WARNING:
The noise emission during actual use
of the power tool can differ from the declared value(s)
depending on the ways in which the tool is used espe-
cially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the
times when the tool is switched off and when it is run-
ning idle in addition to the trigger time).
P i p e
W o o d
w i t h B L 4025
w i t h B L 4050F
) : 8 dB(A)
pA
D.C . 3 6 V - 40 V m a x
1 , are shown in the table.
BL / BL
: Recommended battery
DC
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN
Work mode: cutting boards
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: cutting wooden beams
Vibration emission (a
Uncertainty (K) : 1.8 m/s
NOTE: The declared vibration total value(s) has been
m e a s u r e d i n a c c o r d a n c e w i t h a s t a n d a r d t e s t m e t h o d
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
4 ENGLISH
JR002G
3 2 m m
-1
0 - 3 , 000 m i n
13 0 m m
255 m m
43 6 m m
473 m m
4.6 - 5.8 k g
5 / BL / BL 5 F / BL
RA / DC RB / DC RC
8 1- -11:
2
) : 8.5 m/s
h , B
2
2
) . m/s
h , W B
2
8 F