Prior To Operation; How To Use - HIKOKI RP 3608DB Instrucciones De Manejo

English
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it
has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged
with UC18YSL3 is taken out, wait for a minimum of
3 seconds before reinserting it to continue charging. If
the battery is reinserted within 3 seconds, the battery
may not be properly charged.

PRIOR TO OPERATION

WARNING
Before use, check the following. 1 to 2 should be
checked before insert the battery.
1. Confi rm that the vacuum switch is OFF. (Fig. 3)
If, without knowing that the vacuum switch is ON, the
battery is inserted, the appliance will start suddenly,
causing unexpected accidents. The vacuum switch will
be turned on by pushing "ON" and it will be turned off by
returning it to "OFF". Be sure to check that the vacuum
switch is OFF.
2. Order of use for batteries
When two batteries are installed, the battery with the
least remaining power is used fi rst until it is empty.
Once empty, use is automatically switched over to the
other battery.
Use is still possible with a single installed battery.
NOTE
When there is no more remaining power in a battery,
immediately recharge the battery for convenient use
later.
3. Check the fi lter
Referring to "2. Filter installation/confi rmation" the fi lter
should be correctly attached.
4. Inserting the battery (Fig. 4)
As you pull on the clamp lever, open the battery guard.
Next, match the battery with the unit's groove and
fi rmly press the battery in until you hear a click.
CAUTION
Do not touch the terminals. Doing so may result in
cutting your hand on the terminals or other unexpected
injury.
5. Removing the battery (Fig. 4)
When removing the battery from the unit, press the
latches on both sides and slide the battery upwards to
pull it out.
6. Mode change-over switch operation (Fig. 5)
During operation, the suction power will change each
time the mode selection switch is pressed.
7. Auto/manual switch operation (Fig. 6)
Switches between "Auto" and "Manual" each time the
Auto/Manual switch is pressed.

HOW TO USE

CAUTION
Do not use the head top as a footstool or do not sit on
it. Otherwise the appliance begins to move suddenly,
causing an injury.
NOTE
Handle the hose with care. Do not bend the hose by
force, or do not trample it, or do not pull it to move the
cleaner. Moreover, do not put away the hose as it is
bent. Otherwise troubles such as its deformation may
be caused.
1. Connecting the hose (Fig. 7)
Press the attached hose into the suction opening of the
tank until it clicks and connect it. When removing the
hose, pull out the hose while pushing the button of the
suction opening.
2. Filter installation/confi rmation
WARNING
○ Make sure the fi lters (dust fi lter and prefi lter) are always
installed.
Failure to do so may result in damage to the motor.
NOTE
Water cannot be sucked.
(1) Install the fi lter's seam so that it is on the other side of
the hose air intake. (Fig. 8)
(2) Make sure the packing of the prefi lter is hooked on the
lip of the tank.
Next, insert a fi lter damper at the bottom of the prefi lter.
(Fig. 9)
(3) Insert and attach the cloth fi lter to the dust fi lter in the
direction indicated by the arrow. (Fig. 10)
(4) Match the indication of the "hose side" and insert the
dust fi lter. (Fig. 11)
3. Inserting the battery(Fig. 4)
See "4. Inserting the battery" in "PRIOR TO
OPERATION".
4. Connect cordless tools (Fig. 6)
Connect in order of Hose (id 28 mm × 5 m long) and
Joint (A) or Joint (D) (Standard Accessory). Connection
is done by pressing in the direction of the arrow.
5. Switch ON
(1) When linking with electric power tool
○ Push vacuum switch to "ON" position. (Fig. 5)
○ Press Auto/Manual switch and select "Auto". (Fig. 6)
○ Press mode change-over switch and select 1, 2 or 3
according to application. (Fig. 5)
○ Press the product's Auto/Manual switch and the
electric power tool's wireless linking switch to activate
pairing. (See "WIRELESS LINKING FUNCTION")
○ Use the ON/OFF switch of the linked electric power tool
to simultaneously operate this product.
(2) For independent operation
○ Push vacuum switch to "ON" position. (Fig. 5)
○ Press Auto/Manual switch and select "Manual". (Fig. 6)
○ Press mode change-over switch and select 1, 2 or 3
according to application. (Fig. 5)
○ Conduct fl oor cleaning.
14